Related Experiment Video

Updated: Feb 9, 2026

Estimating the Yield of Compounds on the TLC Plate via the Blue-LED Illumination Technique
06:14

Estimating the Yield of Compounds on the TLC Plate via the Blue-LED Illumination Technique

Published on: October 6, 2022

2.3K

CFD modeling of a UV-A LED baffled flat-plate photoreactor for environment applications: a mining wastewater case

John Steven Devia-Orjuela1, Luis Andrés Betancourt-Buitrago1, Fiderman Machuca-Martinez2

  • 1Escuela de Ingenieria Química, Universidad del Valle, Calle 13 No. 100-00, Cali, Colombia.

Environmental Science and Pollution Research International
|June 4, 2018
PubMed

Keywords:
ActinometryCFDCyanocomplexPhotodegradationPhotoreactorUV LED

More Related Videos

Quantification and Whole Genome Characterization of SARS-CoV-2 RNA in Wastewater and Air Samples09:26

Quantification and Whole Genome Characterization of SARS-CoV-2 RNA in Wastewater and Air Samples

Published on: June 30, 2023

1.7K
Development of an Innovative LED-based Illumination Device for In Vitro Application of Photodynamic Therapy with Rose Bengal07:24

Development of an Innovative LED-based Illumination Device for In Vitro Application of Photodynamic Therapy with Rose Bengal

Published on: September 12, 2025

530

Related Concept Videos

Fluid Pressure over Flat Plate of Constant Width01:05

Fluid Pressure over Flat Plate of Constant Width

When a body is submerged in water, it experiences fluid pressure acting normal on its surface and distributed over its area. For better design structures, it is crucial to determine the magnitude and location of the resultant force acting on the surface. In the case of a rectangular plate of constant width submerged in water, the pressure increases with depth, resulting in a linearly varying trapezoidal pressure distribution from the upper to the lower edge of the plate.
The resultant force...
2.5K
Fluid Pressure over Flat Plate of Variable Width01:02

Fluid Pressure over Flat Plate of Variable Width

When a flat plate is submerged in a fluid, the fluid exerts pressure on the plate. This pressure can lead to many different phenomena, including drag and buoyancy. To understand the behavior of the fluid over a flat plate of variable width, it is essential to analyze the distribution of the pressure exerted.
The pressure distribution on the plate can be calculated by determining the force that acts on a differential area strip of the plate. Thus, the magnitude of the force is equal to the...
2.1K
Flat Belts: Problem Solving01:28

Flat Belts: Problem Solving

Flat belts are crucial in many industrial applications as they help transmit power from one pulley to another. The concept of forces and moments is used to determine the maximum moment on a pulley. For instance, consider a flat belt that wraps around two pulleys, A and B, with radii of 30 cm and 10 cm, respectively. The angle between the belt and the horizontal is 20 degrees at the pulleys. As pulley B rotates clockwise and drives pulley A, tension T2 is caused at one end of the belt, while...
835
Frictional Forces on Flat Belts01:28

Frictional Forces on Flat Belts

Flat belts are commonly used in various industrial applications for transmitting power from one pulley to another. When a flat belt is wrapped around a set of pulleys, it experiences different tensions at the driving pulley ends due to the friction between the belt and pulley surface. When the pulley moves in a counterclockwise direction, the tension T2 on the opposite side of the pulley where the belt is moving away from is higher than the tension T1 on the side where the belt is moving...
1.5K
UV–Vis Spectrum01:30

UV–Vis Spectrum

When light passes through a substance, a portion of the light is absorbed while the remaining light is reflected or transmitted. If the molecule absorbs light between the wavelengths of 180–400 nm range, the UV spectrum is obtained, and if it absorbs light in the 400–780 nm wavelength range, the visible spectrum is obtained.     
The UV–Vis spectrum of a molecule is the plot of its absorbance versus wavelength. The plot is drawn by taking molar...
2.2K
UV–Vis Spectrometers01:14

UV–Vis Spectrometers

The absorbance of UV and visible (UV–visible) radiations is measured using a UV–visible spectrophotometer. Deuterium lamps, which emit UV radiation, and tungsten lamps, which produce radiation in the visible region, are used as light sources in UV–visible spectrophotometers. A monochromator or prism is used for diffraction grating, i.e., to split the incoming radiation into different wavelengths. A system of slits is used to focus the desired wavelength on the sample cell.
3.7K