Related Experiment Video

Updated: Feb 9, 2026

Generation of Organoids from Mouse Extrahepatic Bile Ducts
09:13

Generation of Organoids from Mouse Extrahepatic Bile Ducts

Published on: April 23, 2019

10.7K

THE VALUE OF DEFORMATION OF THE BILE DUCTS IN THE DEVELOPMENT OF POSTCHOLECYSTECTOMY SYNDROME

V V Yurchenko

    Eksperimental'Naia I Klinicheskaia Gastroenterologiia = Experimental & Clinical Gastroenterology
    |June 12, 2018
    PubMed

    More Related Videos

    Laparoscopic Common Bile Duct Exploration Followed by Primary Suture Using a Modified Bile Duct Incision05:36

    Laparoscopic Common Bile Duct Exploration Followed by Primary Suture Using a Modified Bile Duct Incision

    Published on: May 2, 2025

    710
    Determining Bile Duct Density in the Mouse Liver07:35

    Determining Bile Duct Density in the Mouse Liver

    Published on: April 30, 2019

    7.4K

    Related Concept Videos

    Bile01:19

    Bile

    Bile is a crucial bodily fluid, characterized by its yellow-green color and alkaline nature. Produced in the liver, it is transported through the common hepatic duct into either the cystic duct, leading to the gallbladder, or directly into the common bile duct. The flow of bile is regulated by the sphincter of Oddi located at the entrance of the duodenum. When this sphincter is closed, bile is redirected to the gallbladder for storage and concentration.
    Bile is released when dietary fats enter...
    4.4K
    Plastic Deformations01:19

    Plastic Deformations

    Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their...
    471
    Plastic Deformations01:14

    Plastic Deformations

    It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
    473
    Temperature Dependent Deformation01:12

    Temperature Dependent Deformation

    In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
    409
    Deformations in a Symmetric Member in Bending01:18

    Deformations in a Symmetric Member in Bending

    When analyzing the deformation of a symmetric prismatic member subjected to bending by equal and opposite couples, it becomes clear that as the member bends, the originally straight lines on its wider faces curve into circular arcs, with a constant radius centered at a point known as Point C. This phenomenon helps to understand the stress and strain distribution within the member more clearly.
    When the member is segmented into tiny cubic elements, it is observed that the primary stress...
    521
    Deformation of Member under Multiple Loadings01:11

    Deformation of Member under Multiple Loadings

    When a rod is made of different materials or has various cross-sections, it must be divided into parts that meet the necessary conditions for determining the deformation. These parts are each characterized by their internal force, cross-sectional area, length, and modulus of elasticity. These parameters are then used to compute the deformation of the entire rod.
    In the case of a member with a variable cross-section, the strain is not constant but depends on the position. The deformation of an...
    484