Related Experiment Video

Updated: Feb 8, 2026

Coronoid-Temporalis Pedicled Flap for Orbital Floor Defect Reconstruction
06:32

Coronoid-Temporalis Pedicled Flap for Orbital Floor Defect Reconstruction

Published on: December 5, 2025

699

Split Calvarial Graft and Titanium Mesh for Reconstruction of Post-Craniotomy Frontal Bone Defect

Shimels Megersa Gema1,2, Mehrnoush Momeni3, Amir Ali Badri3

  • 1Oral and Maxillofacial Surgery, Department of Oral and Maxillofacial Surgery, Tehran University of Medical Sciences, International Campus (TUMS-IC), Tehran, Iran.

Ethiopian Journal of Health Sciences
|July 10, 2018
PubMed
Abstract

Keywords:
Bone GraftCalvarial SplittingCranioplasty

More Related Videos

Repair of a Critical-sized Calvarial Defect Model Using Adipose-derived Stromal Cells Harvested from Lipoaspirate11:31

Repair of a Critical-sized Calvarial Defect Model Using Adipose-derived Stromal Cells Harvested from Lipoaspirate

Published on: October 31, 2012

16.4K
3D Planning and Printing of Patient Specific Implants for Reconstruction of Bony Defects08:15

3D Planning and Printing of Patient Specific Implants for Reconstruction of Bony Defects

Published on: August 4, 2020

7.0K

Related Concept Videos

Mesh Analysis01:20

Mesh Analysis

Mesh analysis is a valuable method for simplifying circuit analysis using mesh currents as key circuit variables. Unlike nodal analysis, which focuses on determining unknown voltages, mesh analysis applies Kirchhoff's voltage law (KVL) to find unknown currents within a circuit. This method is particularly convenient in reducing the number of simultaneous equations that need to be solved.
A fundamental concept in mesh analysis is the definition of meshes and mesh currents. A mesh is a closed...
1.5K
Lumber Defects01:23

Lumber Defects

Lumber defects, which can affect both the appearance and structural integrity of wood, include a variety of growth and manufacturing flaws. Growth defects such as knots and knotholes occur where branches were once attached to the tree trunk, with knotholes forming when these knots fall out. Other natural defects include decay and insect damage, which compromise the wood's strength and durability.
Shakes are minor fractures that run along or across the wood's annual rings, while wane is...
532
Mesh Analysis with Current Sources01:10

Mesh Analysis with Current Sources

Mesh analysis becomes simpler when analyzing circuits with current sources, whether independent or dependent. The presence of current sources reduces the number of equations required for analysis. Two cases illustrate this:
Current Source in One Mesh: The analysis process is straightforward when a current source is found in only one mesh within the circuit. Mesh currents are assigned as usual, with the mesh containing the current source excluded from the analysis. Kirchhoff's voltage law...
2.0K
¹H NMR: Complex Splitting01:13

¹H NMR: Complex Splitting

A proton M that is coupled to a proton X results in doublet signals for M. However, NMR-active nuclei can be simultaneously coupled to more than one nonequivalent nucleus. When M is coupled to a second proton A, such as in styrene oxide, each peak in the doublet is split into another doublet.
Splitting diagrams or splitting tree diagrams are routinely used to depict such complex couplings. While drawing splitting diagrams, the splitting with the larger coupling constant is usually applied...
1.9K
Mesh Analysis for AC Circuits01:12

Mesh Analysis for AC Circuits

In the domain of radio communication, the significance of impedance matching must be considered. It is crucial to ensure the efficient transmission of signals between radio transmitters and receivers. Achieving this balance involves using impedance-matching circuits, with one fundamental configuration comprising a resistor, capacitor, and inductor.
The process of harmonizing these impedances begins with a clear understanding of the input and output signals. Once these signals are known, the...
713
Reconstruction of Signal using Interpolation01:10

Reconstruction of Signal using Interpolation

Signal processing techniques are essential for accurately converting continuous signals to digital formats and vice versa. When a continuous signal is sampled with a period T, the resulting sampled signal exhibits replicas of the original spectrum in the frequency domain, spaced at intervals equal to the sampling frequency. To handle this sampled signal, a zero-order hold method can be applied, which creates a piecewise constant signal by retaining each sample's value until the next...
735