Related Experiment Video

Updated: Feb 8, 2026

Repetitive Transcranial Magnetic Stimulation to the Unilateral Hemisphere of Rat Brain
05:47

Repetitive Transcranial Magnetic Stimulation to the Unilateral Hemisphere of Rat Brain

Published on: October 22, 2016

13.0K

Plastic in the Brain: Delayed Recognition of Progressive Unilateral Hemispheric Lesions

Ali Daneshmand1, Karl N Krecke1, Eelco F M Wijdicks2

  • 1Division of Critical Care Neurology and Radiology, Mayo Clinic, 200 First Street SW, Rochester, MN, 55905, USA.

Neurocritical Care
|July 11, 2018
PubMed
Abstract

Keywords:
AneurysmComplicationsEndovascular treatmentFlow diverter

More Related Videos

Development of a Unilaterally-lesioned 6-OHDA Mouse Model of Parkinson's Disease10:09

Development of a Unilaterally-lesioned 6-OHDA Mouse Model of Parkinson's Disease

Published on: February 14, 2012

52.3K
Atomic Force Microscopy Investigations of DNA Lesion Recognition in Nucleotide Excision Repair10:59

Atomic Force Microscopy Investigations of DNA Lesion Recognition in Nucleotide Excision Repair

Published on: May 24, 2017

10.1K

Related Concept Videos

Cerebral Hemispheres01:05

Cerebral Hemispheres

The human brain, a complex organ, is functionally divided into two cerebral hemispheres—left and right. These hemispheres are interconnected by a structure of paramount importance, the corpus callosum. This substantial bundle of neural fibers is not just a bridge between the hemispheres but a crucial element for the brain's comprehensive functioning. It enables efficient communication between the two hemispheres, allowing each side of the brain to control and receive sensory and motor...
2.5K
Plasticity00:58

Plasticity

Plasticity is the property where an object loses its elasticity and undergoes irreversible deformation, even after the deformation forces are eliminated. If a material deforms irreversibly without increasing stress or load, then this is called ideal plasticity. For example, when a force is applied to an aluminum rod, it changes its shape, but it does not return to its original shape once the force is removed. Plastic deformation or ductility is thus a permanent deformation or change in the...
3.1K
Plasticizers01:31

Plasticizers

Water-reducers, or plasticizers, are chemical admixtures used in concrete to improve strength and workability. These additives reduce the water-cement ratio without compromising workability, lower the cement content while maintaining the same workability, or increase workability to assist concrete placement in inaccessible areas.
Plasticizers function by using surface-active agents to create repulsive electrostatic forces between cement particles. This dispersion enhances the concrete's...
374
Plastic Behavior01:21

Plastic Behavior

A material's elastic behavior is characterized by the disappearance of stress once the load is removed, allowing the material to return to its original state. However, when stress surpasses the yield point, yielding commences, marking the onset of plastic deformation or permanent set. This change from elastic to plastic behavior is influenced by the peak stress value and the duration before the load is removed. An intriguing observation occurs when a specimen is loaded, unloaded, and...
580
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
471
Plastic Deformations01:19

Plastic Deformations

Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their...
471