Related Experiment Video

Updated: Feb 8, 2026

Magnetically Induced Rotating Rayleigh-Taylor Instability
06:42

Magnetically Induced Rotating Rayleigh-Taylor Instability

Published on: March 3, 2017

10.1K

Influence of Coupling Between Rayleigh and SH SAWs on Rotated -Cut LiNbO3 to Their Propagations

Yulin Huang, Jingfu Bao, Xinyi Li

    IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
    |July 12, 2018
    PubMed

    More Related Videos

    Cut-loading: A Useful Tool for Examining the Extent of Gap Junction Tracer Coupling Between Retinal Neurons10:11

    Cut-loading: A Useful Tool for Examining the Extent of Gap Junction Tracer Coupling Between Retinal Neurons

    Published on: January 12, 2012

    15.8K
    Influenza Virus Propagation in Embryonated Chicken Eggs06:56

    Influenza Virus Propagation in Embryonated Chicken Eggs

    Published on: March 19, 2015

    45.6K

    Related Concept Videos

    Propagation of Waves01:07

    Propagation of Waves

    When a wave propagates from one medium to another, part of it may get reflected in the first medium, and part of it may get transmitted to the second medium. In such a case, the interface of the two mediums can be considered as a boundary that is neither fixed nor free.
    Consider a scenario where a wave propagates from a string of low linear mass density to a string of high linear mass density. In such a case, the reflected wave is out of phase with respect to the incident wave, however the...
    3.0K
    Propagation of Action Potentials01:23

    Propagation of Action Potentials

    The propagation of an action potential refers to the process by which a nerve impulse, or "action potential," travels along a neuron.
    Neurons (nerve cells) have a resting membrane potential, with a slightly negative charge inside compared to outside. This is maintained by ion channels, such as sodium (Na+) and potassium (K+) channels, which control the flow of ions. When a stimulus, like a touch or a signal from another neuron, triggers the neuron, sodium channels open, allowing sodium ions to...
    9.5K
    Spin–Spin Coupling: Two-Bond Coupling (Geminal Coupling)01:20

    Spin–Spin Coupling: Two-Bond Coupling (Geminal Coupling)

    Two NMR-active nuclei bonded to a central atom can be involved in geminal or two-bond coupling. Geminal coupling is commonly seen between diastereotopic protons in chiral molecules and unsymmetrical alkenes, among others.
    The central atom need not be NMR-active because its electrons are affected by the electron polarization of the spin-active atoms. However, spin information is transmitted less effectively than in one-bond coupling, and 2J values are usually weaker than 1J values. The energy of...
    1.7K
    Spin–Spin Coupling: Three-Bond Coupling (Vicinal Coupling)01:22

    Spin–Spin Coupling: Three-Bond Coupling (Vicinal Coupling)

    Vicinal or three-bond coupling is commonly observed between protons attached to adjacent carbons. Here, nuclear spin information is primarily transferred via electron spin interactions between adjacent C‑H bond orbitals. This generally favors the antiparallel arrangement of spins, so 3J values are usually positive.
    The extent of coupling depends on the C‑C bond length, the two H‑C‑C angles, any electron-withdrawing substituents, and the dihedral angle between the involved orbitals. The...
    1.5K
    Cut-off Frequency of BJT01:17

    Cut-off Frequency of BJT

    Cut-off frequencies in Bipolar Junction Transistors (BJTs) mark the transition between the signal's pass band and stop band, influencing their performance in amplifying or attenuating frequencies. These frequencies are crucial for designing BJTs to meet specific operational requirements in electronic circuits.
    Alpha Cut-Off Frequency: Pertinent to the common-base configuration, the alpha cut-off frequency defines the upper-frequency limit at which the current gain, alpha, remains stable. As...
    1.4K
    Brick Cutting Techniques01:08

    Brick Cutting Techniques

    Brick-cutting techniques involve various tools and methods to shape bricks for construction. A mason's hammer with a chisel-pointed end is used for basic shaping through sharp, precise strikes. For more complex shapes requiring higher precision, a power saw with a water-cooled diamond blade is used.
    Cut bricks are categorized by size. Bricks cut to half their original length are called half-bats, while those cut to three-fourths their length are known as three-fourth bats.
    Special types of...
    664