Related Experiment Video

Updated: Feb 7, 2026

Research and Development of High-performance Explosives
10:33

Research and Development of High-performance Explosives

Published on: February 20, 2016

18.3K

Study on the Multi-Spectral True Temperature Pyrometer for Explosion Transient of Thermo-Baric Explosives

Fu-cai Zhang, Xiao-gang Sun, Jian Xing

    Guang Pu Xue Yu Guang Pu Fen Xi = Guang Pu
    |July 13, 2018
    PubMed

    More Related Videos

    Minimum Burning Pressures of Water-based Emulsion Explosives08:35

    Minimum Burning Pressures of Water-based Emulsion Explosives

    Published on: October 31, 2017

    8.8K
    Coulomb Explosion Imaging as a Tool to Distinguish Between Stereoisomers08:51

    Coulomb Explosion Imaging as a Tool to Distinguish Between Stereoisomers

    Published on: August 18, 2017

    10.9K

    Related Concept Videos

    True Stress and True Strain01:28

    True Stress and True Strain

    Engineering stress is calculated as the load divided by the original, undeformed cross-sectional area. It approximates a material under load. This approximation is especially relevant post-yield in ductile materials. Though engineering stress-strain diagrams are often used for their convenience and accessibility, they can sometimes fall short in accuracy, particularly when dealing with large strain values.
    In contrast, true stress offers a more precise portrayal. It is computed by dividing the...
    849
    Series R—L Circuit Transients01:22

    Series R—L Circuit Transients

    In a series resistor-inductor (R-L) circuit, closing the switch at the start of the time period simulates a three-phase short circuit, a fault condition where all three phases of an unloaded synchronous machine are short-circuited. When there is no fault impedance and no initial current, the initial voltage is determined by the phase angle of the source voltage.
    Using Kirchhoff's Voltage Law (KVL) to analyze this circuit helps determine the total asymmetrical fault current, which consists...
    422
    Transient and Steady-state Response01:24

    Transient and Steady-state Response

    In control systems, test signals are essential for evaluating performance under various conditions. The ramp function is effective for systems undergoing gradual changes, while the step function is suitable for assessing systems facing sudden disturbances. For systems subjected to shock inputs, the impulse function is the most appropriate test signal.
    These test signals are integral in designing control systems to exhibit two key performance aspects: transient response and steady-state...
    577
    Multi-input and Multi-variable systems01:22

    Multi-input and Multi-variable systems

    Cruise control systems in cars are designed as multi-input systems to maintain a driver's desired speed while compensating for external disturbances such as changes in terrain. The block diagram for a cruise control system typically includes two main inputs: the desired speed set by the driver and any external disturbances, such as the incline of the road. By adjusting the engine throttle, the system maintains the vehicle's speed as close to the desired value as possible.
    In the absence of...
    426
    Body Temperature01:25

    Body Temperature

    The body's temperature, measured in degrees, is determined by the balance between heat production and dissipation to the surrounding environment. For instance, if exercising vigorously, the body will produce more heat, causing sweat and dissipating that heat. Despite extreme environmental conditions and physical exertion, the human temperature-control system maintains a constant core body temperature (the temperature of deep tissues, which are the tissues located beneath the skin and other...
    4.9K
    Body Temperature01:07

    Body Temperature

    Body temperature reflects the equilibrium between heat production and heat loss within the body. Most heat is generated by metabolically active tissues, particularly the liver, heart, brain, kidneys, and endocrine organs. At rest, skeletal muscles contribute 20–30% of total heat production, but during vigorous exercise, this can increase up to 30–40 times.
    The average body temperature is approximately 37°C (98.6°F) and typically ranges from 36.1–37.2°C...
    1.5K