Related Experiment Video
Updated: Feb 7, 2026
A Spine Robotic-Assisted Navigation System for Pedicle Screw Placement
Published on: May 11, 2020
Pedicle Screw Designs in Spinal Surgery: Is There a Difference? A Biomechanical Study on Primary and Revision
Wei Ren Daniel Seng1, Siaw Meng Chou2, Shiblee S Siddiqui1
1Department of Orthopaedic Surgery, Tan Tock Seng Hospital, National Health Group, Nanyang, Singapore.
Study Design:
An experimental laboratory-based biomechanical study.
Objective:
The objective of this study was to evaluate, in a synthetic bone model, the difference in primary and revision pull-out strength using pedicle screws of different thread designs.
Summary Of Background Data:
Over the past few decades, there has been a growing interest in optimizing the screw pull-out strength using various screw designs (single-thread, mixed-thread, dual-thread). Although primary pull-out strength has been studied previously, little is known about revision pull-out strength of different pedicle screws.
Methods:
The pull-out strengths of three different pedicle screw designs (single-thread, mixed-thread, dual-thread) were tested in standardized polyurethane foam in three sequences. Sequence 1: A 6.5 mm screw was inserted into the foam block and the primary pull-out strength measured. Sequence 2: A 6.5 mm screw was inserted, removed, and then reinserted into the same foam block. The revision pull-out strength was then measured. Sequence 3: A 6.5 mm screw was inserted, removed and a 7.5-mm screw of the same thread design was reinserted. The revision pull-out strength was then measured.
Results:
The primary pull-out strength was similar across screw designs, although dual-thread screws showed higher primary pull-out strength (2628.8 N) compared to single-thread screws (2184.4 N, P < 0.05). For revision pull-out strength, the mixed-thread screws had significant reduction in revision pull-out strength of 18.6% (1890.2 N, P = 0.0173). Revision with a larger diameter screw improved the pull-out strength back to baseline. Single and dual-thread screws showed no significant reduction in revision pull-out strength.
Conclusion:
The dual-threaded screws provided the strongest primary pull-out strength for spinal fixation. The mixed-thread screws, however, had the poorest revision pull-out strength, decreasing by 18.6% compared to other screw designs. In cases in which mixed-threaded screws have to be revised (at the index or revision surgery), surgeons should consider the use of larger diameter screws to improve the pull-out strength.
Level Of Evidence:
5.
Related Concept Videos
01:20Study Designs in Epidemiology
Observational studies are those where the researcher does not intervene but rather observes natural variations. They include cross-sectional, cohort, and...
01:15Study Design in Statistics
Does aspirin reduce the risk of heart attacks? Is one brand of fertilizer more effective at growing roses than another? Is fatigue as dangerous to a driver as the influence of alcohol? Questions like these are answered using randomized experiments with proper...
01:21Screw: Problem Solving
To evaluate the...
01:16Self-Locking Screw
A square-threaded screw jack carrying a load is considered self-locking if the screw retains its position even after the moment applied to it is removed.
03:05Acid Strength and Molecular Structure
In the absence of any leveling effect, the acid strength of binary compounds of hydrogen with nonmetals (A) increases as the H-A bond strength decreases down a group in the periodic table. For group 17, the order of increasing acidity is HF < HCl < HBr < HI. Likewise, for group 16, the order of increasing acid strength is H2O < H2S < H2Se < H2Te. Across a row in the periodic table, the acid strength of binary hydrogen compounds increases with increasing...
01:17Frictional Forces on Screws
A jack with a square-threaded screw is a mechanical device used to lift heavy loads by applying a force at its handle. When the force is applied, the screw turns, raising the load. The screw can...