Accuracy of frozen section in determining meningioma subtype and grade

Richard A Prayson1

  • 1Department of Anatomic Pathology, Cleveland Clinic, United States.

Insights

Frozen section analysis of meningiomas shows significant discrepancies in grading and subtyping compared to final diagnoses. This impacts accurate intraoperative assessment of brain tumors, particularly higher-grade lesions.

Area of Science:

  • Neuropathology
  • Surgical Pathology
  • Oncology

Background:

  • Frozen section intraoperative consultation is standard for brain tumor evaluation during surgery.
  • This technique has recognized limitations in diagnostic specificity.

Purpose of the Study:

  • To retrospectively assess the concordance between frozen section and final diagnoses for meningioma subtype and grade.
  • To identify common discrepancies in frozen section evaluations of meningiomas.

Main Methods:

  • Retrospective review of 424 consecutive meningioma cases.
  • Comparison of frozen section diagnoses with final histopathological diagnoses regarding tumor subtype and World Health Organization (WHO) grade.

Main Results:

  • A discrepancy was observed in 26.9% of cases (114/424).
  • Transitional meningiomas were frequently misclassified at frozen section.
  • Higher-grade meningiomas (WHO grades II and III) showed low concordance (26.2%), with frequent under-grading of atypical meningiomas as WHO grade I.

Conclusions:

  • Discrepancies in frozen section evaluation of meningiomas, especially for higher-grade tumors, are common.
  • Tumor sampling and heterogeneity are likely causes for these diagnostic inaccuracies.

Related Concept Videos

Improving Translational Accuracy02:07

Improving Translational Accuracy

Base complementarity between the three base pairs of mRNA codon and the tRNA anticodon is not a failsafe mechanism. Inaccuracies can range from a single mismatch to no correct base pairing at all. The free energy difference between the correct and nearly correct base pairs can be as small as 3 kcal/ mol. With complementarity being the only proofreading step, the estimated error frequency would be one wrong amino acid in every 100 amino acids incorporated. However, error frequencies observed in...
15.0K
Improving Translational Accuracy02:07

Improving Translational Accuracy

3.7K
Uncertainty in Measurement: Accuracy and Precision03:37

Uncertainty in Measurement: Accuracy and Precision

Scientists typically make repeated measurements of a quantity to ensure the quality of their findings and to evaluate both the precision and the accuracy of their results. Measurements are said to be precise if they yield very similar results when repeated in the same manner. A measurement is considered accurate if it yields a result that is very close to the true or the accepted value. Precise values agree with each other; accurate values agree with a true value. 
102.4K
Graded Potential01:19

Graded Potential

Graded potentials are localized fluctuations in the cell membrane's electrical charge, commonly found in the dendrites of neurons. The magnitude of these potential changes depends on the strength of the initiating stimulus. In a membrane at its resting potential, a graded potential signifies a voltage shift either above -70 mV or below -70 mV.
Graded potentials fall into two categories: depolarizing and hyperpolarizing. Depolarizing graded potentials typically occur when sodium (Na+) or...
7.1K
Accuracy and Precision01:52

Accuracy and Precision

Scientists typically make repeated measurements of a quantity to ensure the quality of their findings and to evaluate both the precision and the accuracy of their results. Measurements are said to be precise if they yield very similar results when repeated in the same manner. A measurement is considered accurate if it yields a result that is very close to the true or the accepted value. Precise values agree with each other; accurate values agree with a true value.  Highly accurate...
15.5K
Accuracy, limits, and approximation01:28

Accuracy, limits, and approximation

Accuracy, limits, and approximations are common in many fields, especially in engineering calculations. These concepts are imperative for ensuring that a given value is as close as possible to its true value.
Accuracy is defined as the closeness of the measured value to the true or actual value. In engineering mechanics, repeated measurements are taken during theoretical or experimental analyses to ensure that the result is precise and accurate.
The accuracy of any solution is based on the...
1.3K