Related Experiment Video

Updated: Feb 7, 2026

Safety Precautions and Operating Procedures in an ABSL-4 Laboratory: 3. Aerobiology
11:13

Safety Precautions and Operating Procedures in an ABSL-4 Laboratory: 3. Aerobiology

Published on: October 3, 2016

15.2K

Chlorination and chloramination of benzophenone-3 and benzophenone-4 UV filters

Peizeng Yang1, Deyang Kong2, Yuefei Ji1

  • 1Department of Environmental Science and Engineering, Nanjing Agricultural University, Nanjing 210095, China.

Ecotoxicology and Environmental Safety
|August 5, 2018
PubMed

Keywords:
Benzophenone-3Benzophenone-4ChloraminationChlorinationDisinfection by-products

More Related Videos

The Synthesis of [Sn10SiSiMe334]2- Using a Metastable SnI Halide Solution Synthesized via a Co-condensation Technique12:43

The Synthesis of [Sn10SiSiMe334]2- Using a Metastable SnI Halide Solution Synthesized via a Co-condensation Technique

Published on: November 28, 2016

9.1K
A Direct, Regioselective and Atom-Economical Synthesis of 3-Aroyl-N-hydroxy-5-nitroindoles by Cycloaddition of 4-Nitronitrosobenzene with Alkynones07:30

A Direct, Regioselective and Atom-Economical Synthesis of 3-Aroyl-N-hydroxy-5-nitroindoles by Cycloaddition of 4-Nitronitrosobenzene with Alkynones

Published on: January 21, 2020

8.7K

Related Concept Videos

Passive Filters01:27

Passive Filters

Passive filters are utilized to shape the frequency spectrum of signals across a diverse array of applications. These filters, using only passive elements like resistors (R), inductors (L), and capacitors (C), are capable of selectively allowing or blocking certain frequency ranges without the need for external power sources.
Low-Pass Filters
Low-pass filters are designed to transmit signals with frequencies lower than the cutoff frequency, ωc, and attenuate those above it. The cutoff...
1.0K
Radical Substitution: Allylic Chlorination01:31

Radical Substitution: Allylic Chlorination

Typically, when alkenes react with halogens at low temperatures, an addition reaction occurs. However, upon increasing the temperature or under reaction conditions that form radicals, providing a low but steady concentration of halogen radicals, allylic substitution reaction is favored. This is because allylic hydrogens are very reactive as the formed intermediate is resonance stabilized. For example, when propene is treated with chlorine in the gas phase at 400 °C, it undergoes allylic...
3.2K
Active Filters01:25

Active Filters

Active filters are electronic circuits that use operational amplifiers (op-amps), resistors, and capacitors to filter out unwanted frequency components from a signal. A first-order low-pass active filter is designed to pass signals with a frequency lower than a certain cutoff frequency and attenuate frequencies higher than that cutoff frequency. The transfer function for a first-order low-pass active filter is:
1.3K
Electrophilic Aromatic Substitution: Chlorination and Bromination of Benzene01:15

Electrophilic Aromatic Substitution: Chlorination and Bromination of Benzene

Chlorination and bromination are important classes of electrophilic aromatic substitutions, where benzene reacts with chlorine or bromine in the presence of a Lewis acid catalyst to give halogenated substitution products. A Lewis acid such as aluminium chloride or ferric chloride catalyzes the chlorination, and ferric bromide catalyzes the bromination reactions. During the bromination of alkenes, bromine polarizes and becomes electrophilic. However, in the bromination of benzene, the bromine...
11.3K
UV–Vis Spectrum01:30

UV–Vis Spectrum

When light passes through a substance, a portion of the light is absorbed while the remaining light is reflected or transmitted. If the molecule absorbs light between the wavelengths of 180–400 nm range, the UV spectrum is obtained, and if it absorbs light in the 400–780 nm wavelength range, the visible spectrum is obtained.     
The UV–Vis spectrum of a molecule is the plot of its absorbance versus wavelength. The plot is drawn by taking molar...
2.1K
UV–Vis Spectrometers01:14

UV–Vis Spectrometers

The absorbance of UV and visible (UV–visible) radiations is measured using a UV–visible spectrophotometer. Deuterium lamps, which emit UV radiation, and tungsten lamps, which produce radiation in the visible region, are used as light sources in UV–visible spectrophotometers. A monochromator or prism is used for diffraction grating, i.e., to split the incoming radiation into different wavelengths. A system of slits is used to focus the desired wavelength on the sample cell.
3.7K