Related Experiment Video

Updated: Feb 6, 2026

Measurement of Protein Turnover Rates in Senescent and Non-Dividing Cultured Cells with Metabolic Labeling and Mass Spectrometry
08:52

Measurement of Protein Turnover Rates in Senescent and Non-Dividing Cultured Cells with Metabolic Labeling and Mass Spectrometry

Published on: April 6, 2022

4.1K

Habitat, latitude and body mass influence the temperature dependence of metabolic rate

J P DeLong1, G Bachman2, J P Gibert3

  • 1School of Biological Sciences, University of Nebraska-Lincoln, Lincoln, NE 68588, USA jpdelong@unl.edu.

Biology Letters
|August 31, 2018
PubMed

Keywords:
climate adaptationcolder is betterhotter is bettermetabolic cold adaptationmetabolic rate

More Related Videos

Isolation, Propagation, and Identification of Bacterial Species with Hydrocarbon Metabolizing Properties from Aquatic Habitats10:03

Isolation, Propagation, and Identification of Bacterial Species with Hydrocarbon Metabolizing Properties from Aquatic Habitats

Published on: December 7, 2021

5.4K
Measurement of Metabolic Rate in Drosophila using Respirometry04:31

Measurement of Metabolic Rate in Drosophila using Respirometry

Published on: June 24, 2014

20.3K

Related Concept Videos

Temperature Dependence on Reaction Rate02:55

Temperature Dependence on Reaction Rate

The Collision Theory
Atoms, molecules, or ions must collide before they can react with each other. Atoms must be close together to form chemical bonds. This premise is the basis for a theory that explains many observations regarding chemical kinetics, including factors affecting reaction rates.
The collision theory is based on the postulates that (i) the reaction rate is proportional to the rate of reactant collisions, (ii) the reacting species collide in an orientation allowing contact between...
89.1K
Habitat Fragmentation02:31

Habitat Fragmentation

Habitat fragmentation describes the division of a more extensive, continuous habitat into smaller, discontinuous areas. Human activities such as land conversion, as well as slower geological processes leading to changes in the physical environment, are the two leading causes of habitat fragmentation. The fragmentation process typically follows the same steps: perforation, dissection, fragmentation, shrinkage, and attrition.
21.4K
Body Temperature01:25

Body Temperature

The body's temperature, measured in degrees, is determined by the balance between heat production and dissipation to the surrounding environment. For instance, if exercising vigorously, the body will produce more heat, causing sweat and dissipating that heat. Despite extreme environmental conditions and physical exertion, the human temperature-control system maintains a constant core body temperature (the temperature of deep tissues, which are the tissues located beneath the skin and other...
4.8K
Body Temperature01:07

Body Temperature

Body temperature reflects the equilibrium between heat production and heat loss within the body. Most heat is generated by metabolically active tissues, particularly the liver, heart, brain, kidneys, and endocrine organs. At rest, skeletal muscles contribute 20–30% of total heat production, but during vigorous exercise, this can increase up to 30–40 times.
The average body temperature is approximately 37°C (98.6°F) and typically ranges from 36.1–37.2°C...
1.5K
Metabolic Rate01:25

Metabolic Rate

The human body is a powerhouse of energy, with every cell performing numerous functions that require energy. This energy production and consumption is measured by the metabolic rate, which quantifies the total heat generated by all the body's chemical reactions and mechanical work. This measurement helps to determine the rate of kilocalorie (kcal) consumption needed to fuel all ongoing activities.
The Basal Metabolic Rate (BMR) measures the energy expended at rest.
Several factors influence...
1.3K
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
407