Related Experiment Video

Updated: Feb 5, 2026

Bioelectric Analyses of an Osseointegrated Intelligent Implant Design System for Amputees
14:31

Bioelectric Analyses of an Osseointegrated Intelligent Implant Design System for Amputees

Published on: July 15, 2009

14.5K

Osseointegration of Coarse and Fine Textured Implants Manufactured by Electron Beam Melting and Direct Metal Laser

David S Ruppert1, Ola L A Harrysson1,2, Denis J Marcellin-Little1,2,3

  • 1Department of Biomedical Engineering, University of North Carolina-NC State University, Chapel Hill-Raleigh, North Carolina.

3D Printing and Additive Manufacturing
|September 8, 2018
PubMed

Keywords:
additive manufactured implantsbone-implant interfacedirect metal laser sinteringelectron beam meltingosseointegration of transcutaneous prostheses

More Related Videos

Determining the Mechanical Strength of Ultra-Fine-Grained Metals05:04

Determining the Mechanical Strength of Ultra-Fine-Grained Metals

Published on: November 22, 2021

2.6K
Quantitative Analysis of Vacuum Induction Melting by Laser-induced Breakdown Spectroscopy03:49

Quantitative Analysis of Vacuum Induction Melting by Laser-induced Breakdown Spectroscopy

Published on: June 10, 2019

7.7K

Related Concept Videos

Shape and Texture of Coarse Aggregate01:25

Shape and Texture of Coarse Aggregate

Aggregate shape is classified based on the relative sharpness or roundness of the edges and corners. This classification includes categories like rounded, angular, elongated, and flaky, each with specific characteristics. Rounded aggregates, fully shaped by attrition, are typical of river or seashore gravel, while angular aggregates, such as crushed rock, have well-defined edges. Aggregates that are elongated and flaky are less desirable, as they can reduce the workability and strength of...
689
Metallic Solids02:37

Metallic Solids

Metallic solids such as crystals of copper, aluminum, and iron are formed by metal atoms. The structure of metallic crystals is often described as a uniform distribution of atomic nuclei within a “sea” of delocalized electrons. The atoms within such a metallic solid are held together by a unique force known as metallic bonding that gives rise to many useful and varied bulk properties.
All metallic solids exhibit high thermal and electrical conductivity, metallic luster, and malleability....
20.7K
Alkali Metals03:06

Alkali Metals

Group 1 elements are soft and shiny metallic solids. They are malleable, ductile, and good conductors of heat and electricity. The melting points of the alkali metals are unusually low for metals and decrease going down the group, while the density increases going down the group with the exception of potassium (Table 1).
Table 1: Properties of the alkali metals
24.8K
Properties of Transition Metals02:58

Properties of Transition Metals

Transition metals are defined as those elements that have partially filled d orbitals. As shown in Figure 1, the d-block elements in groups 3–12 are transition elements. The f-block elements, also called inner transition metals (the lanthanides and actinides), also meet this criterion because the d orbital is partially occupied before the f orbitals.
29.9K
Bonding in Metals02:32

Bonding in Metals

Metallic bonds are formed between two metal atoms. A simplified model to describe metallic bonding has been developed by Paul Drüde called the “Electron Sea Model”. 
52.5K
Phase Transitions: Melting and Freezing02:39

Phase Transitions: Melting and Freezing

Heating a crystalline solid increases the average energy of its atoms, molecules, or ions, and the solid gets hotter. At some point, the added energy becomes large enough to partially overcome the forces holding the molecules or ions of the solid in their fixed positions, and the solid begins the process of transitioning to the liquid state or melting. At this point, the temperature of the solid stops rising, despite the continual input of heat, and it remains constant until all of the solid is...
15.2K