Related Experiment Video

Updated: Feb 5, 2026

In Vivo Visualization of Calcium Transients during Fertilization and Early Development in C. elegans
05:11

In Vivo Visualization of Calcium Transients during Fertilization and Early Development in C. elegans

Published on: July 12, 2024

1.0K

Transient visual loss: Transient lesion in the splenium of the corpus callosum

Mucahit Gunaydin1, Faruk Ozsahin2

  • 1Giresun University, Faculty of Medicine, Department of Emergency Medicine, Giresun, Turkey.

Turkish Journal of Emergency Medicine
|September 8, 2018
PubMed
Abstract

Keywords:
Corpus callosumTransient splenium lesionVisual loss

More Related Videos

Author Spotlight: Assessing Ischemic Stroke Damage Through Middle Cerebral Artery Occlusion Model05:32

Author Spotlight: Assessing Ischemic Stroke Damage Through Middle Cerebral Artery Occlusion Model

Published on: August 11, 2023

3.0K
Transient Transduction of the Strobilated Forms of Echinococcus granulosus13:25

Transient Transduction of the Strobilated Forms of Echinococcus granulosus

Published on: September 16, 2022

3.6K

Related Concept Videos

Series R—L Circuit Transients01:22

Series R—L Circuit Transients

In a series resistor-inductor (R-L) circuit, closing the switch at the start of the time period simulates a three-phase short circuit, a fault condition where all three phases of an unloaded synchronous machine are short-circuited. When there is no fault impedance and no initial current, the initial voltage is determined by the phase angle of the source voltage.
Using Kirchhoff's Voltage Law (KVL) to analyze this circuit helps determine the total asymmetrical fault current, which consists...
405
Transient and Steady-state Response01:24

Transient and Steady-state Response

In control systems, test signals are essential for evaluating performance under various conditions. The ramp function is effective for systems undergoing gradual changes, while the step function is suitable for assessing systems facing sudden disturbances. For systems subjected to shock inputs, the impulse function is the most appropriate test signal.
These test signals are integral in designing control systems to exhibit two key performance aspects: transient response and steady-state...
571
Line Loss01:10

Line Loss

The different configurations of source-load connections include wye (star) and delta connections. The relationship between line and phase voltages and currents varies depending on the configuration. When the source is supplying power, it is transmitted through the wires to the load, and during this transmission, some power is absorbed by the wires, leading to line loss.
Line loss impacts power delivery efficiency in a balanced three-phase circuit. The symmetry in such a circuit simplifies the...
545
Reducing Line Loss01:18

Reducing Line Loss

In a three-phase circuit, line loss is an indicator of energy dissipated as heat due to the resistance of transmission lines. To address this, incorporating transformers into the system—a step-up transformer at the source and a step-down transformer at the load—is a strategic solution. Two three-phase transformers are introduced to improve this.
With a step-up transformer at the source, the voltage is increased, thereby reducing the current in the transmission lines since power loss in...
390
Energy Losses in Transformers01:21

Energy Losses in Transformers

In an ideal transformer, it is assumed that there are no energy losses, and, hence, all the power at the primary winding is transferred to the secondary winding. However, in reality,  the transformers always have some energy losses, and, hence, the output power obtained at the secondary winding is less than the input power at the primary winding due to energy losses.
There are four main reasons for energy losses in transformers.
The first cause can be  the high resistance of the...
1.3K
Major Losses in Pipes01:28

Major Losses in Pipes

When a fluid flows through a pipe, it experiences energy losses due to frictional resistance along the pipe walls, known as major losses. These energy losses result in a pressure drop, which varies based on the flow conditions — whether laminar or turbulent — and the specific physical properties of the fluid and pipe.
Fluid flow can be classified as laminar or turbulent, primarily based on the Reynolds number. This dimensionless number reflects the relative influence of inertial to viscous...
2.0K