Related Experiment Video

Updated: Feb 5, 2026

Preparation of Chitosan-based Injectable Hydrogels and Its Application in 3D Cell Culture
08:05

Preparation of Chitosan-based Injectable Hydrogels and Its Application in 3D Cell Culture

Published on: September 29, 2017

20.0K

BIORESORPTION OF POROUS 3D-MATERIALS BASED ON CHITOSAN

P V Popryaduhin, G Yu Yukina, D N Suslov

    Tsitologiia
    |September 11, 2018
    PubMed

    More Related Videos

    Supercritical Nitrogen Processing for the Purification of Reactive Porous Materials09:05

    Supercritical Nitrogen Processing for the Purification of Reactive Porous Materials

    Published on: May 15, 2015

    15.4K
    3D Printed Porous Cellulose Nanocomposite Hydrogel Scaffolds06:36

    3D Printed Porous Cellulose Nanocomposite Hydrogel Scaffolds

    Published on: April 24, 2019

    10.2K

    Related Concept Videos

    Members Made of Elastoplastic Material01:19

    Members Made of Elastoplastic Material

    The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
    As the bending moment...
    403
    Genetic Material01:20

    Genetic Material

    Within the human body, a complex and detailed system of trillions of cells works in unison to sustain life. Each cell houses a nucleus, which contains 46 chromosomes divided into 23 pairs. Chromosomes are highly coiled structures made of the genetic material DNA. These chromosomes are essential carriers of genetic information, with half inherited from the mother through her egg and the other half from the father's sperm, combining to create the unique genetic makeup of an individual.
    3.8K
    Bending of Members Made of Several Materials01:11

    Bending of Members Made of Several Materials

    In analyzing a structural member composed of two different materials with identical cross-sectional areas, it is crucial to understand how their distinct elastic properties affect the member's response under load. The analysis involves assessing stress and strain distributions using the transformed section concept, which accounts for variations in material properties.
    Hooke's Law determines stress in each material, stating that stress is proportional to strain but varies due to each material's...
    615
    Bending of Material: Problem Solving01:09

    Bending of Material: Problem Solving

    In this lesson, determine the ratio of the maximum bending moments applied to two metal pipes, given that both pipes can withstand a maximum stress of 100 MPa. Both pipes have an outer radius of 1.8 cm. Pipe A has an inner radius of 1.5 cm, and Pipe B has an inner radius of 1 cm. The ratio of the maximum bending moment applied to two metallic pipes, each with a different inner and outer radius, is determined by considering their dimensions. The inner radius of the first pipe is 1.5 cm, and for...
    534
    Circular Shafts - Elastoplastic Materials01:24

    Circular Shafts - Elastoplastic Materials

    The study of solid circular shafts under stress shows that within the elastic limit, stress increases directly to the distance from the shaft's center. This relationship holds until the shaft reaches a critical point of stress, beyond which it begins to yield, marking the transition from elastic to plastic deformation. At this crucial juncture, the maximum torque the shaft can endure without permanent deformation is determined, signifying the limit of its elastic behavior.
    As torque on the...
    499
    Stress-Strain Diagram - Ductile Materials01:24

    Stress-Strain Diagram - Ductile Materials

    The stress-strain relationship in ductile materials such as structural steel or aluminium is intricate and progresses through several stages. When a specimen is loaded, it initially exhibits a linear length increase, depicted by a steep straight line on the stress-strain diagram. It indicates the material is elastically deforming and will return to its original shape once unloaded. However, when a critical stress value is reached, plastic deformation begins. This stage sees substantial...
    2.1K