Related Experiment Video

Updated: Feb 5, 2026

A Porcine Corneal Endothelial Organ Culture Model Using Split Corneal Buttons
08:36

A Porcine Corneal Endothelial Organ Culture Model Using Split Corneal Buttons

Published on: October 6, 2019

7.6K

Corneal Endothelial Cell Density in Uveal Coloboma Associated With Microcornea

Rohit Dhakal1, Ashik Mohamed2, Sunita Chaurasia3

  • 1Brien Holden Institute of Optometry and Vision Sciences, LV Prasad Eye Institute, Hyderabad, India.

Cornea
|September 18, 2018
PubMed
Abstract

More Related Videos

Corneal Donor Tissue Preparation for Endothelial Keratoplasty08:37

Corneal Donor Tissue Preparation for Endothelial Keratoplasty

Published on: June 12, 2012

28.2K
Growth of Human and Sheep Corneal Endothelial Cell Layers on Biomaterial Membranes05:20

Growth of Human and Sheep Corneal Endothelial Cell Layers on Biomaterial Membranes

Published on: February 6, 2020

8.3K

Related Concept Videos

Density00:56

Density

Density is an important characteristic of substances, crucial in determining whether an object sinks or floats in a fluid. Its SI unit is kg/m3, and its cgs unit is g/cm3. The density of an object helps in identifying its composition, and also reveals information about the phase of the matter and its substructure. The densities of liquids and solids are roughly comparable, consistent with the fact that their atoms are in close contact. However, gases have much lower densities than liquids and...
19.9K
Current Density01:21

Current Density

The total amount of current flowing through one unit value of a cross-sectional area is referred to as current density. If the current flow is uniform, the amount of current flowing through a conductor is the same at all points along the conductor, even if the conductor area varies. The current density consists of the local magnitude and direction of the charge flow, which varies from point to point. Current density is measured in amperes per meter square, and direction is defined as the net...
5.1K
Strain-Energy Density01:20

Strain-Energy Density

Understanding the strain energy density in materials under axial load is crucial for evaluating their mechanical behavior and durability. When a rod is subjected to such a load, it elongates and stores energy, known as strain energy, as potential energy within the material. This energy is measured in terms of energy per unit volume.
In the elastic region of a material, the relationship between the stress and the strain is linear and follows Hooke's Law. The strain energy density in this region...
923
Bulk Density of Aggregate01:22

Bulk Density of Aggregate

Bulk density refers to the mass of aggregate particles that would fill a unit volume. The concept of bulk density originates from the inability to pack aggregate particles in a manner that completely eliminates void spaces. Hence, the term bulk refers to the volume that encompasses both the aggregates and the voids. This measurement is crucial when aggregates are batched by volume and is used to convert quantities by mass to volume.
Most natural mineral aggregates, like sand and gravel,...
1.2K
Density and Archimedes' Principle01:05

Density and Archimedes' Principle

When a lump of clay is dropped into water, it sinks. But if the same lump of clay is molded into the shape of a boat, it starts to float. Because of its shape, the clay boat displaces more water than the lump and experiences a greater buoyant force, even though its mass is the same. The same holds true for steel ships. The average density of an object majorly determines if the object will float. If an object's average density is less than that of the surrounding fluid, it will float. The...
8.9K
Applications of the Ideal Gas Law: Molar Mass, Density, and Volume03:43

Applications of the Ideal Gas Law: Molar Mass, Density, and Volume

The volume occupied by one mole of a substance is its molar volume. The ideal gas law, PV = nRT,  suggests that the volume of a given quantity of gas and the number of moles in a given volume of gas vary with changes in pressure and temperature. At standard temperature and pressure, or STP (273.15 K and 1 atm), one mole of an ideal gas (regardless of its identity) has a volume of about 22.4 L — this is referred to as the standard molar volume.
63.5K