Related Experiment Video
Updated: Feb 5, 2026

Preparation of Expanded Chitin Foams and their Use in the Removal of Aqueous Copper
Published on: February 27, 2021
[Preparation and biocompatibility of nano polypyrrole/chitin composite membrane]
Haishan Jiao1, Ping Cao2, Ying Chen3
1School of Clinical Medicine, Suzhou Vocational Health College, Suzhou Jiangsu, 215009, P.R.China.jiaohaishan@szhct.edu.cn.
Objective:
To prepare nano polypyrrole (PPy)/chitin composite membrane and observe their biocompatibility.
Methods:
The nano PPy was synthesized by microemulsion polymerization, blended with chitosan and then formed membranes. The membranes were then modified by acetylation to get the experimental membranes (nano PPy/chitin composite membranes, group A). The chitosan membranes (group B) and chitin ones (group C) modified by acetylation acted as control. Scanning electron microscopy and FT-IR spectra were used to identify the nano PPy and the membranes of each group. And the conductivity of membranes of each group was measured. Schwann cells were co-cultured in vitro with each group membranes to observe the biocompatibility by inverted microscope observing, living cell staining, cell counting, and immunofluorescence staining. The lysozyme solution was used to evaluate the degradation of the membranes in vitro.
Results:
The FT-IR spectra showed that the characteristic vibrational absorption peaks of C=C from nano PPy appeared at 1 543.4 cm -1 and 1 458.4 cm -1. Scanning electron microscopy observation revealed that the size of nano PPy particles was about 100-200 nm. The nano PPy particles were synthesized. It was successful to turn chitosan to chitin by the acetylation, which was investigated by FT-IR analysis of membranes in groups A and C. The characteristic peaks of the amide Ⅱ band around 1 562 cm -1 appeared after acetylated modification. Conductivity test showed that the conductivity of membranes in group A was about (1.259 2±0.005 7)×10 -3 S/cm, while the conductivity of the membranes in groups B and C was not detected. The nano PPy particles uniformly distributed on the surface of membranes in group A were observed by scanning electron microscope; the membranes in control groups were smooth. As a result, the nano PPy/chitin composite membranes with electrical conductivity were obtained. The cultured Schwann cells were found to survive with good function by fluorescein diacetate live cell staining, soluble protein-100 immunofluorescence staining, and inverted microscope observing. The cell counting showed that the proliferation of Schwann cells after 2 days and 4 days of group A was more than that of the two control groups, and the differences were significant ( P<0.05). It indicated that the nano PPy/chitin composite membranes had better ability of adhesion and proliferation than those of chitosan and chitin membranes. The degradation of membranes in vitro showed that the degradation rates of membranes in groups A and C were significantly higher than those in group B at all time points ( P<0.05). In a word, the degradation performance of the membranes modified by acetylation was better than that of chitosan membranes under the same condition.
Conclusion:
The nano PPy and chitosan can be blended and modified by acetylation successfully. Nano PPy/chitin composite membranes had electrical conductivity, degradability, and good biocompatibility in vitro.
More Related Videos
07:08Solution Blow Spinning of Polymeric Nano-Composite Fibers for Personal Protective Equipment
Published on: March 18, 2021
06:26Experimental Implementation of a New Composite Fabrication Method: Exposing Bare Fibers on the Composite Surface by the Soft Layer Method
Published on: October 6, 2017
Related Concept Videos
Classifying Matter by Composition
According to its composition, the matter can be classified into two broad categories — pure substances and mixtures.
A pure substance is a form of matter that has a constant composition throughout with uniform properties. For example, any sample of sucrose has the same composition and same physical properties, such as melting point, color, and sweetness, regardless of the source from which it is isolated.
A mixture is composed of two or...
Composite Bodies
Composite bodies have widespread applications in mechanical engineering, from automobiles to aircraft to rockets. For example, an automobile wheel comprises...
Composition of Blood
Formed elements constitute the remaining 45% of the blood volume. These...
Composition of Body Fluids
Moments of Inertia for Composite Areas
The second moment of area, also known as the moment of inertia, measures a structure's resistance to bending. It is calculated by...
Composition of Blood Plasma