Related Experiment Video

Updated: Feb 4, 2026

Multi-target Parallel Processing Approach for Gene-to-structure Determination of the Influenza Polymerase PB2 Subunit
22:10

Multi-target Parallel Processing Approach for Gene-to-structure Determination of the Influenza Polymerase PB2 Subunit

Published on: June 28, 2013

13.7K

Multi-material Ti6Al4V & PEEK cellular structures produced by Selective Laser Melting and Hot Pressing: A

F Bartolomeu1, M Buciumeanu2, M M Costa1

  • 1Center for Micro-Electro Mechanical Systems (CMEMS-UMinho), University of Minho, Campus de Azurém, 4800-058 Guimarães, Portugal.

Journal of the Mechanical Behavior of Biomedical Materials
|September 29, 2018
PubMed

Keywords:
Cellular structuresHot PressingMulti-materialSelective Laser MeltingTi6Al4V-PEEKTribocorrosion

More Related Videos

Quantitative Analysis of Vacuum Induction Melting by Laser-induced Breakdown Spectroscopy03:49

Quantitative Analysis of Vacuum Induction Melting by Laser-induced Breakdown Spectroscopy

Published on: June 10, 2019

7.7K
Determining Tribocorrosion Rate and Wear-Corrosion Synergy of Bulk and Thin Film Aluminum Alloys07:12

Determining Tribocorrosion Rate and Wear-Corrosion Synergy of Bulk and Thin Film Aluminum Alloys

Published on: September 11, 2018

11.9K

Related Concept Videos

Phase Transitions: Melting and Freezing02:39

Phase Transitions: Melting and Freezing

Heating a crystalline solid increases the average energy of its atoms, molecules, or ions, and the solid gets hotter. At some point, the added energy becomes large enough to partially overcome the forces holding the molecules or ions of the solid in their fixed positions, and the solid begins the process of transitioning to the liquid state or melting. At this point, the temperature of the solid stops rising, despite the continual input of heat, and it remains constant until all of the solid is...
15.2K
Hot Weather Concreting01:20

Hot Weather Concreting

Concreting at elevated temperatures accelerates the hydration process, leading to quicker setting but potentially reducing the long-term strength of the concrete structure. Additionally, low air humidity fosters rapid moisture loss from the concrete, resulting in reduced workability, pronounced plastic shrinkage, and a higher likelihood of crazing.
Mitigating the heat increase in concrete can be economically achieved by shading aggregate stockpiles to prevent heating from solar radiation,...
316
Comparing Intermolecular Forces: Melting Point, Boiling Point, and Miscibility02:34

Comparing Intermolecular Forces: Melting Point, Boiling Point, and Miscibility

Intermolecular forces are attractive forces that exist between molecules. They dictate several bulk properties, such as melting points, boiling points, and solubilities (miscibilities) of substances. Molar mass, molecular shape, and polarity affect the strength of different intermolecular forces, which influence the magnitude of physical properties across a family of molecules.
Temporary attractive forces like dispersion are present in all molecules, whether they are polar or nonpolar. They...
51.5K
What is Natural Selection?01:32

What is Natural Selection?

Natural selection is an evolutionary process in which individuals with survival-promoting traits reproduce at higher rates. These favorable traits become more common within a population or species. Naturally selected traits initially arise via random genetic mutations. In order for selection to occur, there must be variation within a population, the trait controlling the variation must be heritable, and there must be an evolutionary advantage for variation in the trait.
129.5K
Masonry in Cold and Hot Weather Conditions01:21

Masonry in Cold and Hot Weather Conditions

In cold weather, masonry construction requires specific precautions to ensure mortar does not freeze before curing, as this can significantly weaken its strength and watertightness. Mortar temperature should be maintained between 60°F and 80°F to support proper hydration and curing. Below 40°F, mortar water must be heated, but should not exceed 120°F as high temperatures can reduce mortar's compressive and bond strength.
Other key practices include keeping masonry units...
348
Members Made of Elastoplastic Material01:19

Members Made of Elastoplastic Material

The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
As the bending moment...
402