Related Experiment Video

Updated: Feb 4, 2026

Towards Biomimicking Wood: Fabricated Free-standing Films of Nanocellulose, Lignin, and a Synthetic Polycation
11:26

Towards Biomimicking Wood: Fabricated Free-standing Films of Nanocellulose, Lignin, and a Synthetic Polycation

Published on: June 17, 2014

17.1K

Nanocellulose and chitosan based films as low cost, green piezoelectric materials

Aleksi Hänninen1, Essi Sarlin2, Inari Lyyra1

  • 1BioMediTech Institute and Faculty of Biomedical Sciences and Engineering, Tampere University of Technology, Korkeakoulunkatu 10, Tampere, 33720, Finland.

Carbohydrate Polymers
|October 6, 2018
PubMed

Keywords:
ChitosanNanocellulosePiezoelectric sensitivityPiezoelectricitySolvent casting

More Related Videos

Characterization of Full Set Material Constants and Their Temperature Dependence for Piezoelectric Materials Using Resonant Ultrasound Spectroscopy07:44

Characterization of Full Set Material Constants and Their Temperature Dependence for Piezoelectric Materials Using Resonant Ultrasound Spectroscopy

Published on: April 27, 2016

10.1K
Formation of Human Periodontal Ligament Cell Spheroids on Chitosan Films04:14

Formation of Human Periodontal Ligament Cell Spheroids on Chitosan Films

Published on: June 19, 2019

5.7K

Related Concept Videos

Green Algae01:21

Green Algae

Green algae, also referred to as chlorophytes, are different from red algae in having the chloroplasts containing chlorophylls a and b, which give them their distinct green hue. However, they lack phycobiliproteins, preventing them from developing the red or blue-green pigmentation seen in red algae. In terms of photosynthetic pigment composition, green algae closely resemble plants and share a close evolutionary relationship with them. Taxonomically Green algae belong to Phylum Chlorophyta in...
840
Members Made of Elastoplastic Material01:19

Members Made of Elastoplastic Material

The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
As the bending moment...
402
Genetic Material01:20

Genetic Material

Within the human body, a complex and detailed system of trillions of cells works in unison to sustain life. Each cell houses a nucleus, which contains 46 chromosomes divided into 23 pairs. Chromosomes are highly coiled structures made of the genetic material DNA. These chromosomes are essential carriers of genetic information, with half inherited from the mother through her egg and the other half from the father's sperm, combining to create the unique genetic makeup of an individual.
3.8K
Bending of Members Made of Several Materials01:11

Bending of Members Made of Several Materials

In analyzing a structural member composed of two different materials with identical cross-sectional areas, it is crucial to understand how their distinct elastic properties affect the member's response under load. The analysis involves assessing stress and strain distributions using the transformed section concept, which accounts for variations in material properties.
Hooke's Law determines stress in each material, stating that stress is proportional to strain but varies due to each material's...
615
Bending of Material: Problem Solving01:09

Bending of Material: Problem Solving

In this lesson, determine the ratio of the maximum bending moments applied to two metal pipes, given that both pipes can withstand a maximum stress of 100 MPa. Both pipes have an outer radius of 1.8 cm. Pipe A has an inner radius of 1.5 cm, and Pipe B has an inner radius of 1 cm. The ratio of the maximum bending moment applied to two metallic pipes, each with a different inner and outer radius, is determined by considering their dimensions. The inner radius of the first pipe is 1.5 cm, and for...
533
Circular Shafts - Elastoplastic Materials01:24

Circular Shafts - Elastoplastic Materials

The study of solid circular shafts under stress shows that within the elastic limit, stress increases directly to the distance from the shaft's center. This relationship holds until the shaft reaches a critical point of stress, beyond which it begins to yield, marking the transition from elastic to plastic deformation. At this crucial juncture, the maximum torque the shaft can endure without permanent deformation is determined, signifying the limit of its elastic behavior.
As torque on the...
497