Related Experiment Video

Updated: Feb 4, 2026

Pancreatic Tissue Dissection to Isolate Viable Single Cells
08:04

Pancreatic Tissue Dissection to Isolate Viable Single Cells

Published on: May 26, 2023

4.0K

Single transluminal gateway transcystic multiple drainage for extensive walled-off pancreatic necrosis - a

Mateusz Jagielski1, Marian Smoczyński1, Krystian Adrych1

  • 1Department of Gastroenterology and Hepatology, Medical University of Gdansk, Gdansk, Poland.

Przeglad Gastroenterologiczny
|October 11, 2018
PubMed
Abstract

Keywords:
endoscopic drainagewalled-off pancreatic necrosis

More Related Videos

Author Spotlight: Advancements in Retroperitoneal Approach for Necrotizing Pancreatitis03:42

Author Spotlight: Advancements in Retroperitoneal Approach for Necrotizing Pancreatitis

Published on: March 15, 2024

1.2K
Single-cell Transcriptomic Analyses of Mouse Pancreatic Endocrine Cells10:05

Single-cell Transcriptomic Analyses of Mouse Pancreatic Endocrine Cells

Published on: September 30, 2018

11.7K

Related Concept Videos

Cavity Drainage and Flashings in Masonry walls01:20

Cavity Drainage and Flashings in Masonry walls

Typically, a cavity wall consists of two wythes separated by a gap of at least 2 inches, which may contain insulation while still maintaining a minimum clear space of 1 inch to facilitate adequate drainage. Advanced methods like the insertion of a continuous drainage mat can further reduce this space while ensuring effective moisture expulsion.
Weep holes, strategically placed at the base of the cavity, are critical for draining accumulated water. These openings are created by leaving head...
462
Bioavailability Study Design: Single Versus Multiple Dose Studies01:11

Bioavailability Study Design: Single Versus Multiple Dose Studies

Bioavailability studies are essential for understanding how a drug is absorbed, distributed, metabolized, and excreted in the body. These studies assess the extent and rate at which the active pharmaceutical agent becomes available at the site of action. The design of bioavailability studies can involve single-dose or multiple-dose regimens, each with distinct advantages and limitations.Single-dose studies are the preferred approach due to their simplicity and reduced drug exposure for...
243
Necrosis01:16

Necrosis

Necrosis is considered as an “accidental” or unexpected form of cell death that ends in cell lysis. The first noticeable mention of “necrosis” was in 1859 when Rudolf Virchow used this term to describe advanced tissue breakdown in his compilation titled “Cell Pathology”.
Morphological Manifestations of Necrosis
Necrotic cells show different types of morphological appearance depending on the type of tissue and infection. In coagulative necrosis, cells become...
6.6K
Load along a Single Axis01:29

Load along a Single Axis

In structural engineering, the analysis of beams subjected to varying loads is a critical aspect of understanding the behavior and performance of these structural elements. A common scenario involves a beam subjected to a combination of different load distributions.
Consider a beam of length L subjected to a varying load, which is a combination of parabolic and trapezoidal load distribution along the x-axis. In this case, it is essential to determine the resultant loads, their locations, and...
646
Single Pipe Systems01:24

Single Pipe Systems

In pipe flow analysis, problems are typically categorized into three types — Type I, Type II, and Type III — based on the known parameters and the desired outcome. Each type of problem addresses specific engineering requirements using fluid properties, pipe characteristics, and operational conditions.
In a Type I problem, fluid properties (density and viscosity), pipe characteristics (including diameter, length, and surface roughness), and the flow rate or average velocity are...
454
Angular Momentum: Single Particle01:10

Angular Momentum: Single Particle

Angular momentum is directed perpendicular to the plane of the rotation, and its magnitude depends on the choice of the origin. The perpendicular vector joining the linear momentum vector of an object to the origin is called the “lever arm.” If the lever arm and linear momentum are collinear, then the magnitude of the angular momentum is zero. Therefore, in this case, the object rotates about the origin such that it lies on the rim of the circumference defined by the lever arm...
7.8K