Related Experiment Video

Updated: Feb 3, 2026

Printing Fabrication of Bulk Heterojunction Solar Cells and In Situ Morphology Characterization
07:32

Printing Fabrication of Bulk Heterojunction Solar Cells and In Situ Morphology Characterization

Published on: January 29, 2017

11.6K

Incipient Bulk Polycrystal Plasticity Observed by Synchrotron In-Situ Topotomography

Henry Proudhon1, Nicolas Guéninchault2, Samuel Forest3

  • 1MINES ParisTech, PSL Research University, MAT-Centre des Matériaux, CNRS UMR 7633, BP 87 91003 Evry, France. henry.proudhon@mines-paristech.fr.

Materials (Basel, Switzerland)
|October 21, 2018
PubMed

Keywords:
X-ray diffraction imagingfinite element simulationin situ experimentlattice curvaturepolycrystal plasticityrocking curvetopotomography

More Related Videos

Cell Culture on Silicon Nitride Membranes and Cryopreparation for Synchrotron X-ray Fluorescence Nano-analysis08:26

Cell Culture on Silicon Nitride Membranes and Cryopreparation for Synchrotron X-ray Fluorescence Nano-analysis

Published on: December 10, 2019

9.9K
Non-invasive 3D-Visualization with Sub-micron Resolution Using Synchrotron-X-ray-tomography08:51

Non-invasive 3D-Visualization with Sub-micron Resolution Using Synchrotron-X-ray-tomography

Published on: May 27, 2008

13.6K

Related Concept Videos

Plasticity00:58

Plasticity

Plasticity is the property where an object loses its elasticity and undergoes irreversible deformation, even after the deformation forces are eliminated. If a material deforms irreversibly without increasing stress or load, then this is called ideal plasticity. For example, when a force is applied to an aluminum rod, it changes its shape, but it does not return to its original shape once the force is removed. Plastic deformation or ductility is thus a permanent deformation or change in the...
3.1K
Plasticizers01:31

Plasticizers

Water-reducers, or plasticizers, are chemical admixtures used in concrete to improve strength and workability. These additives reduce the water-cement ratio without compromising workability, lower the cement content while maintaining the same workability, or increase workability to assist concrete placement in inaccessible areas.
Plasticizers function by using surface-active agents to create repulsive electrostatic forces between cement particles. This dispersion enhances the concrete's...
368
Plastic Behavior01:21

Plastic Behavior

A material's elastic behavior is characterized by the disappearance of stress once the load is removed, allowing the material to return to its original state. However, when stress surpasses the yield point, yielding commences, marking the onset of plastic deformation or permanent set. This change from elastic to plastic behavior is influenced by the peak stress value and the duration before the load is removed. An intriguing observation occurs when a specimen is loaded, unloaded, and...
579
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
444
Plastic Deformations01:19

Plastic Deformations

Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their...
465
Bulk Modulus01:21

Bulk Modulus

The bulk modulus is a scientific term used to describe a material's resistance to uniform compression. It is the proportionality constant that links a change in pressure to the resulting relative volume change.
778