Related Experiment Video

Updated: Feb 3, 2026

Vascularized Composite Upper Limb Allograft Harvesting for Proximal Arm Allotransplantation
08:11

Vascularized Composite Upper Limb Allograft Harvesting for Proximal Arm Allotransplantation

Published on: June 13, 2025

592

Proximal humerus deformity, in a four-limb amputee following meningococcal septicaemia

Adeel Ikram1, Kriti Singhania1, Suhayl Tafazal1

  • 1Department of Trauma and Orthopaedics, Royal Derby Hospital, Derby, UK.

BMJ Case Reports
|October 28, 2018
PubMed

Keywords:
bone and joint infectionsorthopaedic and trauma surgeryorthopaedicspaediatrics

More Related Videos

Bioelectric Analyses of an Osseointegrated Intelligent Implant Design System for Amputees14:31

Bioelectric Analyses of an Osseointegrated Intelligent Implant Design System for Amputees

Published on: July 15, 2009

14.5K
Therapy Interventions for Upper Limb Amputees Undergoing Selective Nerve Transfers07:59

Therapy Interventions for Upper Limb Amputees Undergoing Selective Nerve Transfers

Published on: October 29, 2021

4.2K

Related Concept Videos

Bones of the Upper Limb: Humerus01:19

Bones of the Upper Limb: Humerus

The upper limb consists of the arm, forearm, wrist, and hand bones. The humerus is the single bone of the upper arm region. Proximally, it has a large, spherical, smooth head that articulates with the glenoid cavity of the scapula to form the glenohumeral or shoulder joint. The margin of the head is the anatomical neck, a residual epiphyseal plate. Laterally it extends to form bony projections called the greater tubercle and the lesser tubercle. Next to the tubercles is the surgical neck, a...
7.2K
Plastic Deformations01:19

Plastic Deformations

Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their...
465
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
444
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
401
Deformations in a Symmetric Member in Bending01:18

Deformations in a Symmetric Member in Bending

When analyzing the deformation of a symmetric prismatic member subjected to bending by equal and opposite couples, it becomes clear that as the member bends, the originally straight lines on its wider faces curve into circular arcs, with a constant radius centered at a point known as Point C. This phenomenon helps to understand the stress and strain distribution within the member more clearly.
When the member is segmented into tiny cubic elements, it is observed that the primary stress...
521
Deformation of Member under Multiple Loadings01:11

Deformation of Member under Multiple Loadings

When a rod is made of different materials or has various cross-sections, it must be divided into parts that meet the necessary conditions for determining the deformation. These parts are each characterized by their internal force, cross-sectional area, length, and modulus of elasticity. These parameters are then used to compute the deformation of the entire rod.
In the case of a member with a variable cross-section, the strain is not constant but depends on the position. The deformation of an...
476