Related Experiment Video

Updated: Feb 2, 2026

Passaging Human Neural Stem Cells
10:16

Passaging Human Neural Stem Cells

Published on: August 22, 2007

15.3K

Phenotypic stability of the human MG-63 osteoblastic cell line at different passages

Susanne Staehlke1, Henrike Rebl1, Barbara Nebe1

  • 1Department of Cell Biology, University Medical Center Rostock, Rostock, Germany.

Cell Biology International
|November 17, 2018
PubMed

Keywords:
MG-63 osteoblastsadhesion receptorsapoptosiscell cycle phasescell signalingintracellular calcium ion mobilization

More Related Videos

Stabilizing Hepatocellular Phenotype Using Optimized Synthetic Surfaces08:50

Stabilizing Hepatocellular Phenotype Using Optimized Synthetic Surfaces

Published on: September 26, 2014

10.6K
Passaging HuES Human Embryonic Stem Cell-lines with Trypsin.09:38

Passaging HuES Human Embryonic Stem Cell-lines with Trypsin.

Published on: October 12, 2006

261.2K

Related Concept Videos

Nuclear Stability03:18

Nuclear Stability

Protons and neutrons, collectively called nucleons, are packed together tightly in a nucleus. With a radius of about 10−15 meters, a nucleus is quite small compared to the radius of the entire atom, which is about 10−10 meters. Nuclei are extremely dense compared to bulk matter, averaging 1.8 × 1014 grams per cubic centimeter. If the earth’s density were equal to the average nuclear density, the earth’s radius would be only about 200 meters.
To hold positively charged protons together...
23.3K
RNA Stability01:53

RNA Stability

Intact DNA strands can be found in fossils, while scientists sometimes struggle to keep RNA intact under laboratory conditions. The structural variations between RNA and DNA underlie the differences in their stability and longevity. Because DNA is double-stranded, it is inherently more stable. The single-stranded structure of RNA is less stable but also more flexible and can form weak internal bonds. Additionally, most RNAs in the cell are relatively short, while DNA can be up to 250 million...
35.7K
Stability01:28

Stability

The time response of a linear time-invariant (LTI) system can be divided into transient and steady-state responses. The transient response represents the system's initial reaction to a change in input and diminishes to zero over time. In contrast, the steady-state response is the behavior that persists after the transient effects have faded.
The stability of an LTI system is determined by the roots of its characteristic equation, known as poles. A system is stable if it produces a bounded...
418
Stability of structures01:14

Stability of structures

In mechanical engineering, the stability of systems under various forces is critical for designing durable and efficient structures. One fundamental way to explore these concepts is by analyzing systems like two rods connected at a pivot point, O, with a torsional spring of spring constant k at the pivot point. This system is similar in appearance to a scissor jack used to change tires on a car. In this case, the arms of the linkage (equivalent to the rods in this system) are entirely vertical,...
523
Pole and System Stability01:24

Pole and System Stability

The transfer function is a fundamental concept representing the ratio of two polynomials. The numerator and denominator encapsulate the system's dynamics. The zeros and poles of this transfer function are critical in determining the system's behavior and stability.
Simple poles are unique roots of the denominator polynomial. Each simple pole corresponds to a distinct solution to the system's characteristic equation, typically resulting in exponential decay terms in the system's...
966
Multimachine Stability01:25

Multimachine Stability

Multimachine stability analysis is crucial for understanding the dynamics and stability of power systems with multiple synchronous machines. The objective is to solve the swing equations for a network of M machines connected to an N-bus power system.
In analyzing the system, the nodal equations represent the relationship between bus voltages, machine voltages, and machine currents. The nodal equation is given by:
581