Related Experiment Video

Updated: Feb 2, 2026

Atomic Force Microscopy Cantilever-Based Nanoindentation: Mechanical Property Measurements at the Nanoscale in Air and Fluid
08:58

Atomic Force Microscopy Cantilever-Based Nanoindentation: Mechanical Property Measurements at the Nanoscale in Air and Fluid

Published on: December 2, 2022

3.8K

Static and Fatigue Tests on Cementitious Cantilever Beams Using Nanoindenter

Yidong Gan1, Hongzhi Zhang2, Branko Šavija3

  • 1Microlab, Faculty of Civil Engineering and Geosciences, Delft University of Technology, 2628 CN Delft, The Netherlands. y.gan@tudelft.nl.

Micromachines
|November 30, 2018
PubMed

Keywords:
cement pastefatiguemicromechanicsminiaturized cantilever beamnanoindenter

More Related Videos

Ultrasonic Fatigue Testing in the Tension-Compression Mode06:54

Ultrasonic Fatigue Testing in the Tension-Compression Mode

Published on: March 7, 2018

11.2K
Crack Monitoring in Resonance Fatigue Testing of Welded Specimens Using Digital Image Correlation05:30

Crack Monitoring in Resonance Fatigue Testing of Welded Specimens Using Digital Image Correlation

Published on: September 29, 2019

8.7K

Related Concept Videos

Impact Loading on a Cantilever Beam01:13

Impact Loading on a Cantilever Beam

The analysis of a cantilever beam with a circular cross-section subjected to impact loading at its free end illustrates the conversion of potential energy from a dropped object into kinetic energy, which is then absorbed by the beam as strain energy. This process is crucial for understanding how materials behave under dynamic loads, which is important in fields such as construction and aerospace.
When an object is dropped onto the free end of a cantilever, its potential energy due to gravity is...
896
Fatigue01:21

Fatigue

Fatigue occurs when materials rupture under repeated or fluctuating loads, even at stress levels far below their static breaking strength. It typically results in brittle failure, even for ductile materials. It is a critical consideration in designing machines and structural components subjected to repetitive or varying loads. The nature of these loadings can range from fluctuating loads like unbalanced pump impellers causing vibrations to repeatedly bending a thin steel rod wire back and forth...
838
Beams01:30

Beams

Beams are integral components of structural engineering and construction, designed to support loads applied at various points along their length. These long, straight members can be classified based on geometry, cross-section, support type, and equilibrium condition.
Based on geometry, beams can be straight, tapered, or curved. Straight beams are the most common type and have a constant cross-section throughout their length. Tapered beams, on the other hand, have a varying cross-section along...
1.9K
Static Equilibrium - I01:05

Static Equilibrium - I

A rigid body is said to be in dynamic equilibrium when both its linear and angular acceleration are zero, relative to an inertial frame of reference. This means that a body in equilibrium can be moving, but only when its linear and angular velocities are constant. A rigid body is said to be in static equilibrium when it is at rest in the selected frame of reference. The distinction between static equilibrium (e.g., a state of rest) and dynamic equilibrium (e.g, a state of uniform motion) is...
18.9K
Static Equilibrium - II01:07

Static Equilibrium - II

Static equilibrium is a special case in mechanics that is very important in everyday life. It occurs when the net force and the net torque on an object or system are both zero. This means that both the linear and angular accelerations are zero. Thus, the object is at rest, or its center of mass is moving at a constant velocity. However, this does not mean that no forces are acting on the object within the system. In fact, there are very few scenarios on Earth in which no forces are acting upon...
10.0K
Static Friction01:18

Static Friction

Static friction is a force that opposes the relative motion or tendency of motion between two surfaces in contact. It plays a crucial role in our daily lives, from walking on the ground to driving a car.
For example, consider a scenario where a truck is connected to a car by a rope, ready to tow it along a road. When no external force is applied by the truck, the car remains stationary and is said to be in static equilibrium. In this case, the forces acting on the car, such as gravity and the...
1.4K