Related Experiment Video

Updated: Feb 1, 2026

Ammonia Synthesis at Low Pressure
08:14

Ammonia Synthesis at Low Pressure

Published on: August 23, 2017

27.3K

Temperature dependent control of the solubility of gallium nitride in supercritical ammonia using mixed mineralizer

Daisuke Tomida1, Kiyoshi Kuroda2, Kentaro Nakamura2

  • 1Institute of Multidisciplinary Research for Advanced Materials, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai, 980-8577, Japan. daisuke.tomida.e4@tohoku.ac.jp.

Chemistry Central Journal
|December 5, 2018
PubMed

Keywords:
Acidic mineralizerAmmonothermalGallium nitrideSolubilitySupercritical ammonia

More Related Videos

Preparing Silica Aerogel Monoliths via a Rapid Supercritical Extraction Method06:54

Preparing Silica Aerogel Monoliths via a Rapid Supercritical Extraction Method

Published on: February 28, 2014

21.8K
Supercritical Nitrogen Processing for the Purification of Reactive Porous Materials09:05

Supercritical Nitrogen Processing for the Purification of Reactive Porous Materials

Published on: May 15, 2015

15.3K

Related Concept Videos

Temperature Dependence on Reaction Rate02:55

Temperature Dependence on Reaction Rate

The Collision Theory
Atoms, molecules, or ions must collide before they can react with each other. Atoms must be close together to form chemical bonds. This premise is the basis for a theory that explains many observations regarding chemical kinetics, including factors affecting reaction rates.
The collision theory is based on the postulates that (i) the reaction rate is proportional to the rate of reactant collisions, (ii) the reacting species collide in an orientation allowing contact between...
89.0K
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
399
Solubility Equilibria03:07

Solubility Equilibria

Solubility equilibria are established when the dissolution and precipitation of a solute species occur at equal rates. These equilibria underlie many natural and technological processes, ranging from tooth decay to water purification. An understanding of the factors affecting compound solubility is, therefore, essential to the effective management of these processes. This section applies previously introduced equilibrium concepts and tools to systems involving dissolution and precipitation.
The...
57.4K
Factors Affecting Solubility04:01

Factors Affecting Solubility

Compared with pure water, the solubility of an ionic compound is less in aqueous solutions containing a common ion (one also produced by dissolution of the ionic compound). This is an example of a phenomenon known as the common ion effect, which is a consequence of the law of mass action that may be explained using Le Chȃtelier’s principle. Consider the dissolution of silver iodide:
37.1K
Physical Properties Affecting Solubility02:19

Physical Properties Affecting Solubility

Solutions of Gases in Liquids
As for any solution, the solubility of a gas in a liquid is affected by the attractive intermolecular forces between solute and solvent species. Unlike solid and liquid solutes, however, there is no solute-solute intermolecular attraction to overcome when a gaseous solute dissolves in a liquid solvent since the atoms or molecules comprising a gas are far separated and experience negligible interactions. Consequently, solute-solvent interactions are the sole...
26.5K
Solubility of Ionic Compounds02:55

Solubility of Ionic Compounds

Solubility is the measure of the maximum amount of solute that can be dissolved in a given quantity of solvent at a given temperature and pressure. Solubility is usually measured in molarity (M) or moles per liter (mol/L). A compound is termed soluble if it dissolves in water.
68.2K