Related Experiment Video

Updated: Feb 1, 2026

Oscillation and Reaction Board Techniques for Estimating Inertial Properties of a Below-knee Prosthesis
08:08

Oscillation and Reaction Board Techniques for Estimating Inertial Properties of a Below-knee Prosthesis

Published on: May 8, 2014

17.3K

The CAD/CAM Compound Prosthesis: Digital Workflow for Fabricating Cement-Retained Zirconia Prosthesis Over

Meisam Faeghinejad, Periklis Proussaefs, Abdulaziz AlHelal

    The International Journal of Periodontics & Restorative Dentistry
    |December 14, 2018
    PubMed

    More Related Videos

    Designing CAD/CAM Surgical Guides for Maxillary Reconstruction Using an In-house Approach08:01

    Designing CAD/CAM Surgical Guides for Maxillary Reconstruction Using an In-house Approach

    Published on: August 24, 2018

    9.5K
    Quasistatic Mechanical Testing for Computer-Aided Design and Manufacturing Occlusal Veneers Cemented to Milled Dentin Analog Material07:42

    Quasistatic Mechanical Testing for Computer-Aided Design and Manufacturing Occlusal Veneers Cemented to Milled Dentin Analog Material

    Published on: December 20, 2024

    853

    Related Concept Videos

    C4 Pathway and CAM01:27

    C4 Pathway and CAM

    Most plants use the C3 pathway for carbon fixation. However, some plants, such as sugar cane, corn, and cacti that grow in hot conditions, use alternative pathways to fix carbon and conserve energy loss due to photorespiration. Photorespiration is the process that occurs when the oxygen concentration is high. Under such conditions, the rubisco enzyme in the Calvin cycle binds O2 instead of CO2, which halts photosynthesis and consumes energy.
    C4 Pathway
    The C4 pathway is used by plants such as...
    49.2K
    Bar Graph01:07

    Bar Graph

    A bar graph is also called a bar chart and consists of bars that are separated from each other. It either uses horizontal or vertical bars to show comparisons among categories. The bars can be rectangles, or they can be rectangular boxes (used in three-dimensional plots). One axis of the graph represents the specific categories being compared, and the other axis shows a discrete value. In this graph, the length of the bar for each category is proportional to the number or percent of individuals...
    22.2K
    Hydration of Cement01:24

    Hydration of Cement

    Hydration of cement is a chemical reaction between cement particles and water. This process occurs primarily through two mechanisms: through-solution and topochemical. In the through-solution process, anhydrous compounds dissolve into their constituents, hydrates form in the solution, and then precipitate from the supersaturated solution. The topochemical process involves solid-state reactions at the cement particle surface. The through-solution process dominates the topochemical process at the...
    920
    Soundness of Cement01:17

    Soundness of Cement

    The soundness of cement refers to the ability of cement paste to retain its volume after setting. Unsound cement can lead to expansion and structural damage due to the presence of free lime, magnesia, and calcium sulfate. Free lime hydrates very slowly, expanding and causing unsoundness, which is difficult to detect because it intercrystallizes with other compounds. Magnesia also reacts with water, forming crystals that can disrupt the cement's structure. Calcium sulfate can create...
    565
    Multiple Bar Graph01:07

    Multiple Bar Graph

    As the name suggests, a multiple bar graph is the same as a bar graph but has multiple bars to depict relationships between different data values. One can include as many parameters as possible. However, each parameter must have the same unit of measurement.
    Each bar or column in the multiple bar graph represents a data value. These graphs are used primarily in interrelating two or more sets of data. The categories of different kinds of data are listed along the horizontal or x-axis, whereas...
    9.3K
    Screw: Problem Solving01:21

    Screw: Problem Solving

    In mechanical engineering, the interaction between a threaded screw shaft and a plate gear involves analyzing the resisting torque on the plate gear that can be overpowered when a specific torsional moment is applied to the shaft. To better comprehend this concept, consider a generic situation with a threaded screw shaft with a given mean radius and lead and a plate gear with a specified mean radius. The coefficient of static friction between the screw and gear is also provided.
    To evaluate the...
    701