Related Experiment Video

Updated: Jan 31, 2026

Treating Low Back Pain in Failed Back Surgery Patients with Multicolumn-lead Spinal Cord Stimulation
04:42

Treating Low Back Pain in Failed Back Surgery Patients with Multicolumn-lead Spinal Cord Stimulation

Published on: June 26, 2018

15.2K

Spontaneous closure of a chronic full thickness macular hole after failed surgery

Jennifer Lee1, Vincent Q Nguyen1, Mallika K Doss1

  • 1Retina Service, Department of Ophthalmology, University of Pittsburgh Medical Center, Pittsburgh, PA, USA.

American Journal of Ophthalmology Case Reports
|December 25, 2018
PubMed
Abstract

Keywords:
Idiopathic macular holeOptical coherence tomographyPolypoidal choroidal vasculopathySpontaneous closureType 1 neovascularization

More Related Videos

A Craniotomy Surgery Procedure for Chronic Brain Imaging09:25

A Craniotomy Surgery Procedure for Chronic Brain Imaging

Published on: February 15, 2008

66.0K
Surgical Swine Model of Chronic Cardiac Ischemia Treated by Off-Pump Coronary Artery Bypass Graft Surgery09:12

Surgical Swine Model of Chronic Cardiac Ischemia Treated by Off-Pump Coronary Artery Bypass Graft Surgery

Published on: March 27, 2018

10.0K

Related Concept Videos

Spontaneity02:21

Spontaneity

A spontaneous process is one that occurs naturally under certain conditions. A nonspontaneous process, on the other hand, will not take place unless it is “driven” by the continual input of energy from an external source. Processes have a natural tendency to occur in one direction under a given set of conditions. Water will naturally flow downhill (spontaneous process), but uphill flow (nonspontaneous process) requires outside intervention such as the use of a pump. Iron exposed to...
29.8K
Hypothesis: Accept or Fail to Reject?01:17

Hypothesis: Accept or Fail to Reject?

The outcome of any hypothesis testing leads to rejecting or not rejecting the null hypothesis. This decision is taken based on the analysis of the data, an appropriate test statistic, an appropriate confidence level, the critical values, and P-values. However, when the evidence suggests that the null hypothesis cannot be rejected, is it right to say, 'Accept' the null hypothesis?
There are two ways to indicate that the null hypothesis is not rejected. 'Accept' the null...
29.5K
Detection of Black Holes01:10

Detection of Black Holes

Although black holes were theoretically postulated in the 1920s, they remained outside the domain of observational astronomy until the 1970s.
Their closest cousins are neutron stars, which are composed almost entirely of neutrons packed against each other, making them extremely dense. A neutron star has the same mass as the Sun but its diameter is only a few kilometers. Therefore, the escape velocity from their surface is close to the speed of light.
Not until the 1960s, when the first neutron...
2.6K
Angle Closure Glaucoma: Treatment01:28

Angle Closure Glaucoma: Treatment

Angle-closure glaucoma, or closed-angle glaucoma, is an eye condition where the iris bulges out and blocks the iridocorneal angle, resulting in a buildup of aqueous humor and increased intraocular pressure. Immediate medical attention is necessary due to the sudden onset of symptoms. The treatment for angle-closure glaucoma includes short-term and long-term approaches. Short-term treatment involves using eye drops like pilocarpine to lower intraocular pressure by increasing aqueous humor...
1.3K
Spontaneous and Induced Mutations01:30

Spontaneous and Induced Mutations

Spontaneous mutations arise infrequently during DNA replication due to errors in the process. A key factor behind these errors is tautomeric shifts in nitrogenous bases, where bases transition from keto to enol forms or amino to imino forms. This shift can alter base-pairing rules, leading to mutations. Additionally, reactive oxygen species (ROS) arising from aerobic metabolism can damage DNA, resulting in depurination (loss of a purine base) or depyrimidination (loss of a pyrimidine base).
2.3K
Design Example: Deciding Thickness of Lubricating Fluid in a Shaft01:23

Design Example: Deciding Thickness of Lubricating Fluid in a Shaft

Effective lubrication between a rotating shaft and its bearing housing is essential in rotating machinery to minimize friction, wear, and energy loss. With carefully controlled thickness and viscosity, the lubricant layer prevents metal-to-metal contact, ensuring smooth operation.
To calculate the required thickness of the lubricant layer, the tangential velocity at the shaft's surface must first be determined. This velocity is calculated by converting the rotational speed to angular velocity...
339