Triplanar Quantitative Radiographic Analysis of the First Metatarsal-Phalangeal Joint in the Hallux Abductovalgus

Todd Hasenstein1, Andrew J Meyr2

  • 1Resident, Temple University Hospital Podiatric Surgical Residency Program, Philadelphia, PA.

Although hallux abductovalgus (HAV) is widely considered to be a triplanar deformity involving the transverse, sagittal, and frontal planes, most of the published literature has focused on evaluating the deformity in only the transverse plane, and we are unaware of any investigation objectively evaluating the relationship among the 3 planes in the setting of HAV deformity. The objective of this investigation was to quantitatively evaluate radiographic measurement of the relationship between the transverse, sagittal, and frontal planes in the HAV deformity. Anteroposterior, lateral, and sesamoid axial radiographs from 42 consecutive feet were evaluated with measurement of the first intermetatarsal angle, hallux abductus angle, metatarsal sesamoid position, first metatarsal inclination angle, sesamoid rotation angle, and tibial sesamoid grade. Variables were graphically depicted against each other on frequency scatter plots with calculation of a regression line and Pearson's correlation coefficient. As transverse plane deformity increased, the frontal plane deformity also tended to increase and the first metatarsal inclination angle tended to decrease. And as frontal plane deformity increased, the first metatarsal inclination angle tended to decrease. To our knowledge, these are the first quantitative and objective data in support of a triplanar component to the HAV deformity, and we believe this reinforces the evaluation of this deformity with emphasis on all 3 planes.

Related Concept Videos

Quantitative Analysis01:12

Quantitative Analysis

Quantitative analysis is a technique for measuring the amount of specific constituents in a sample. When the sample's composition is unknown, qualitative analysis is performed first to identify its components, which ensures that the correct substances are measured during the quantitative phase.
In quantitative analysis, two key measurements are made: the sample quantity and a property proportional to the amount of the analyte (the substance being analyzed). This forms the basis of the...
1.4K
Plastic Deformations01:19

Plastic Deformations

Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their...
465
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
443
Structural Joints: Synovial Joints01:16

Structural Joints: Synovial Joints

Synovial joints are the most common type of joint in the body. A key structural characteristic for a synovial joint is the presence of a joint cavity. This fluid-filled space is where the articulating surfaces of the bones contact each other. Also, unlike fibrous or cartilaginous joints, the articulating bone surfaces at a synovial joint are not directly connected to each other with fibrous connective tissue or cartilage. This gives the bones of a synovial joint the ability to move smoothly...
6.8K
Structural Joints: Fibrous Joints01:03

Structural Joints: Fibrous Joints

Fibrous joints are a type of joint where the bones are connected by fibrous connective tissue. These joints provide stability and minimal to no movement between the articulating bones. There are three types of fibrous joints.
Suture
All the bones of the skull, except for the mandible, are joined to each other by a fibrous joint called a suture. The fibrous connective tissue found at a suture strongly unites the adjacent skull bones and thus helps to protect the brain and form the face. In...
3.8K
Structural Joints: Cartilaginous Joints01:17

Structural Joints: Cartilaginous Joints

As the name indicates, at a cartilaginous joint, the adjacent bones are united by cartilage, a tough but flexible type of connective tissue. Unlike synovial joints, these types of joints lack a joint cavity and involve bones joined together by either hyaline cartilage or fibrocartilage.
There are two types of cartilaginous joints:
Synchondrosis
A synchondrosis ("joined by cartilage") is a cartilaginous joint where bones are connected by hyaline cartilage. Synchondrosis may be temporary...
4.0K