Related Experiment Video

Updated: Jan 31, 2026

Additive Manufacturing of Functionally Graded Ceramic Materials by Stereolithography
06:53

Additive Manufacturing of Functionally Graded Ceramic Materials by Stereolithography

Published on: January 25, 2019

15.1K

Accuracy and retention of denture base fabricated by heat curing and additive manufacturing

Akinori Tasaka1, Satoru Matsunaga2, Kento Odaka3

  • 1Department of Removable Partial Prosthodontics, Tokyo Dental College, Tokyo, Japan; Department of Oral Health Science Center, Tokyo Dental College, Tokyo, Japan.

Journal of Prosthodontic Research
|December 26, 2018
PubMed
Abstract

Keywords:
3D printerAdditive manufacturingCAD/CAMDenture baseRetentive force

More Related Videos

An Additive Manufacturing Technique for the Facile and Rapid Fabrication of Hydrogel-based Micromachines with Magnetically Responsive Components08:17

An Additive Manufacturing Technique for the Facile and Rapid Fabrication of Hydrogel-based Micromachines with Magnetically Responsive Components

Published on: July 18, 2018

7.5K
Characterizing Dissipative Elastic Metamaterials Produced by Additive Manufacturing09:39

Characterizing Dissipative Elastic Metamaterials Produced by Additive Manufacturing

Published on: June 28, 2024

1.6K

Related Concept Videos

Curing of Concrete01:20

Curing of Concrete

The hydration of cement takes place within the water-filled capillary pores. However, environmental elements can disrupt this process by evaporating water from the concrete surfaces. Sealed concrete with a water-cement ratio below 0.5 experiences self-desiccation, leading to water loss. The water loss in concrete is mitigated by curing. This technique involves keeping the concrete saturated to maintain the necessary temperature and moisture conditions, to optimally fill the spaces in the cement...
369
Curing Methods01:26

Curing Methods

Concrete members with a small surface-to-volume ratio are cured by oiling and moistening the forms before casting the concrete member. These forms can be left in place for a prolonged period to prevent moisture loss, and can be wetted if made of a material suitable for wetting. If the forms are removed early, the concrete member is moistened and covered with polythene sheets to maintain moisture. For large horizontal concrete surfaces exposed to dry weather, a temporary covering is suspended...
297
Improving Translational Accuracy02:07

Improving Translational Accuracy

Base complementarity between the three base pairs of mRNA codon and the tRNA anticodon is not a failsafe mechanism. Inaccuracies can range from a single mismatch to no correct base pairing at all. The free energy difference between the correct and nearly correct base pairs can be as small as 3 kcal/ mol. With complementarity being the only proofreading step, the estimated error frequency would be one wrong amino acid in every 100 amino acids incorporated. However, error frequencies observed in...
14.9K
Accelerated Curing of Concrete01:25

Accelerated Curing of Concrete

Accelerating concrete curing is achieved by applying heat and additional moisture. This process accelerates the hydration of the cement, resulting in an earlier strength gain in the concrete. Steam curing is a method wherein the concrete products are either transported through a chamber on a conveyor belt or encased in plastic, allowing steam at atmospheric pressure to circulate freely around them. This process begins with a phase of moist curing that typically lasts between 3 to 5 hours, after...
478
Base-Catalyzed Aldol Addition Reaction01:08

Base-Catalyzed Aldol Addition Reaction

As depicted in Figure 1, base-catalyzed aldol addition involves adding two carbonyl compounds in aqueous sodium hydroxide to form a β-hydroxy carbonyl compound.
4.6K
Conjugate Addition (1,4-Addition) vs Direct Addition (1,2-Addition)01:27

Conjugate Addition (1,4-Addition) vs Direct Addition (1,2-Addition)

α,β-Unsaturated carbonyl compounds with two electrophilic sites, the carbonyl carbon, and the β carbon, are susceptible to nucleophilic attack via two modes: conjugate or 1,4-addition and direct or 1,2-addition.
Conjugate addition results in a thermodynamically stable product. The reaction retains the stronger C=O bond at the expense of the weaker C=C π bond. The process is slow as the β carbon is less electrophilic than the carbonyl carbon.
Direct addition products are...
4.3K