Related Experiment Video

Updated: Jan 30, 2026

Implantation of Total Artificial Heart in Congenital Heart Disease
07:27

Implantation of Total Artificial Heart in Congenital Heart Disease

Published on: July 18, 2014

25.2K

Fetuses with Isolated Congenital Heart Defects Show Normal Cerebral and Extracerebral Fluid Volume Growth: A 3D

F A R Jansen1, E W van Zwet2, S M P Everwijn3

  • 1Leiden University Medical Centre, Department of Obstetrics and Fetal Medicine, Leiden, The Netherlands, f.a.r.jansen@lumc.nl.

Fetal Diagnosis and Therapy
|January 18, 2019
PubMed
Abstract

Keywords:
3D ultrasoundBrain development of the fetusCongenital heart defectsFetal cerebral growth

More Related Videos

A Pipeline to Characterize Structural Heart Defects in the Fetal Mouse08:19

A Pipeline to Characterize Structural Heart Defects in the Fetal Mouse

Published on: December 16, 2022

2.4K
Analysis of Congenital Heart Defects in Mouse Embryos Using Qualitative and Quantitative Histological Methods08:28

Analysis of Congenital Heart Defects in Mouse Embryos Using Qualitative and Quantitative Histological Methods

Published on: March 10, 2020

7.4K

Related Concept Videos

Development of the Sexual Organs in the Embryo and Fetus01:15

Development of the Sexual Organs in the Embryo and Fetus

Development of the reproductive organs in an embryo starts from a bipotential state. This means the early embryo can develop either male or female reproductive organs. The formation of these organs begins with the growth of gonadal ridges that arise from the intermediate mesoderm during the fifth week of development.
Near the gonadal ridges, two duct systems are present: the mesonephric ducts (Wolffian ducts) and paramesonephric ducts (Müllerian ducts). These ducts form the basis for the...
3.6K
Lumber Defects01:23

Lumber Defects

Lumber defects, which can affect both the appearance and structural integrity of wood, include a variety of growth and manufacturing flaws. Growth defects such as knots and knotholes occur where branches were once attached to the tree trunk, with knotholes forming when these knots fall out. Other natural defects include decay and insect damage, which compromise the wood's strength and durability.
Shakes are minor fractures that run along or across the wood's annual rings, while wane is...
516
Normal Stress01:19

Normal Stress

Normal stress is a type of stress that occurs when forces act perpendicular, or normal, to a material's cross-sectional area. This stress often arises in structures when subjected to axial loading, which is the application of force along the axis of an object. A practical example of this can be found in bridge truss members.
When a rod is under axial loading, the internal forces and corresponding stress are normal to the plane of the section, so it is termed normal stress. It's important to...
1.4K
Normal Distribution01:11

Normal Distribution

The normal, a continuous distribution, is the most important of all the distributions. Its graph is a bell-shaped symmetrical curve, which is observed in almost all disciplines. Some of these include psychology, business, economics, the sciences, nursing, and, of course, mathematics. Some instructors may use the normal distribution to help determine students’ grades. Most IQ scores are normally distributed. Often real-estate prices fit a normal distribution. The normal distribution is...
17.2K
Anatomy of the Heart01:27

Anatomy of the Heart

The human heart is made up of three layers of tissue that are surrounded by the pericardium, a membrane that protects and confines the heart. The outermost layer, closest to the pericardium, is the epicardium. The pericardial cavity separates the pericardium from the epicardium. Beneath the epicardium is the myocardium, the middle layer, and the endocardium, the innermost layer. There are four chambers of the heart: the right atrium, the right ventricle, the left atrium, and the left ventricle.
119.7K
Normal and Shear Force01:14

Normal and Shear Force

When a beam is subjected to different loads, such as weight, pressure, or other external forces, internal forces are generated within the beam. These forces can have a significant impact on the overall stability and strength of the structure. Engineers use various methods to analyze and determine the magnitude and direction of these internal forces. One common technique used to determine internal forces in beams is the method of sections. This method involves considering an imaginary point or...
3.3K