Related Experiment Video

Updated: Jan 30, 2026

Development and Functionalization of Electrolyte-Gated Graphene Field-Effect Transistor for Biomarker Detection
07:51

Development and Functionalization of Electrolyte-Gated Graphene Field-Effect Transistor for Biomarker Detection

Published on: February 1, 2022

3.8K

Efficient DBT removal from diesel oil by CVD synthesized N-doped graphene as a nanoadsorbent: Equilibrium, kinetic

Seyyed Salar Meshkat1, Alimorad Rashidi2, Zeinab Hoseini Dastgerdi1

  • 1Faculty of Chemical Engineering, Urmia University of Technology, Urmia, Iran.

Ecotoxicology and Environmental Safety
|January 27, 2019
PubMed

Keywords:
Chemical vapor depositionDesulfurizationIsothermN-doped graphene

More Related Videos

Scalable Syntheses of Graphene Oxide and Reduced Graphene Oxide using Cascade Design Oxidation and Highly Basic Reduction Reactions08:57

Scalable Syntheses of Graphene Oxide and Reduced Graphene Oxide using Cascade Design Oxidation and Highly Basic Reduction Reactions

Published on: July 3, 2025

2.0K
Synthesis and Functionalization of 3D Nano-graphene Materials: Graphene Aerogels and Graphene Macro Assemblies10:23

Synthesis and Functionalization of 3D Nano-graphene Materials: Graphene Aerogels and Graphene Macro Assemblies

Published on: November 5, 2015

14.5K

Related Concept Videos

Relation of DFT to z-Transform01:20

Relation of DFT to z-Transform

The Discrete Fourier Transform (DFT) is a crucial tool for analyzing the frequency content of discrete-time signals. It converts a sequence of N samples from the time domain into its corresponding sequence in the frequency domain, where each sample represents a specific frequency component.
To understand how the DFT works, it's helpful to consider the z-transform, which is a method for representing discrete sequences in the complex frequency domain. The z-transform involves summing the...
822
Dynamic Equilibrium02:20

Dynamic Equilibrium

A reversible chemical reaction represents a chemical process that proceeds in both forward (left to right) and reverse (right to left) directions. When the rates of the forward and reverse reactions are equal, the concentrations of the reactant and product species remain constant over time and the system is at equilibrium. A special double arrow is used to emphasize the reversible nature of the reaction. The relative concentrations of reactants and products in equilibrium systems vary greatly;...
62.4K
Otto and Diesel Cycle01:27

Otto and Diesel Cycle

An Otto engine is a four-stroke engine that uses a mixture of gasoline and air as the working fuel. The fuel is injected into the cylinder, and the piston is moved completely down so that the cylinder is at maximum volume. By moving the piston up, adiabatic compression takes place. The spark plug ignites the gasoline-air mixture, and the burning fuel adds heat to the system at a constant volume. The heated mixture expands adiabatically and gets further cooled by exhausting heat, and this cyclic...
3.7K
Free Energy and Equilibrium02:56

Free Energy and Equilibrium

The free energy change for a process may be viewed as a measure of its driving force. A negative value for ΔG represents a driving force for the process in the forward direction, while a positive value represents a driving force for the process in the reverse direction. When ΔGrxn is zero, the forward and reverse driving forces are equal, and the process occurs in both directions at the same rate (the system is at equilibrium).
Recall that Q is the numerical value of the mass action...
27.2K
Calculating the Equilibrium Constant02:46

Calculating the Equilibrium Constant

The equilibrium constant for a reaction is calculated from the equilibrium concentrations (or pressures) of its reactants and products. If these concentrations are known, the calculation simply involves their substitution into the Kc expression.
For example, gaseous nitrogen dioxide forms dinitrogen tetroxide according to this equation:
37.9K
Solution Equilibrium and Saturation01:59

Solution Equilibrium and Saturation

Imagine adding a small amount of sugar to a glass of water, stirring until all the sugar has dissolved, and then adding a bit more. You can repeat this process until the sugar concentration of the solution reaches its natural limit, a limit determined primarily by the relative strengths of the solute-solute, solute-solvent, and solvent-solvent attractive forces. You can be certain that you have reached this limit because, no matter how long you stir the solution, undissolved sugar remains. The...
21.9K