Related Experiment Video

Updated: Jan 30, 2026

High-pressure, High-temperature Deformation Experiment Using the New Generation Griggs-type Apparatus
12:30

High-pressure, High-temperature Deformation Experiment Using the New Generation Griggs-type Apparatus

Published on: April 3, 2018

19.5K

Experience of treating the Talipes equinovarus deformity with Ponsetti technique at district level

Badaruddin Sahito1, Nusrat Rasheed1, Dileep Kumar1

  • 1Department of orthopaedic surgery, Dow University of Health Sciences, Karachi, Pakistan.

JPMA. the Journal of the Pakistan Medical Association
|January 31, 2019
PubMed
Abstract

Keywords:
TEV, Ponsetti casting, District level.

More Related Videos

A Microfluidic Technique to Probe Cell Deformability09:47

A Microfluidic Technique to Probe Cell Deformability

Published on: September 3, 2014

11.8K
A Virtual Simulation Experiment of Mechanics: Material Deformation and Failure Based on Scanning Electron Microscopy06:54

A Virtual Simulation Experiment of Mechanics: Material Deformation and Failure Based on Scanning Electron Microscopy

Published on: January 20, 2023

3.6K

Related Concept Videos

Plastic Deformations01:19

Plastic Deformations

Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their...
459
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
431
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
390
Deformations in a Symmetric Member in Bending01:18

Deformations in a Symmetric Member in Bending

When analyzing the deformation of a symmetric prismatic member subjected to bending by equal and opposite couples, it becomes clear that as the member bends, the originally straight lines on its wider faces curve into circular arcs, with a constant radius centered at a point known as Point C. This phenomenon helps to understand the stress and strain distribution within the member more clearly.
When the member is segmented into tiny cubic elements, it is observed that the primary stress...
514
Deformation of Member under Multiple Loadings01:11

Deformation of Member under Multiple Loadings

When a rod is made of different materials or has various cross-sections, it must be divided into parts that meet the necessary conditions for determining the deformation. These parts are each characterized by their internal force, cross-sectional area, length, and modulus of elasticity. These parameters are then used to compute the deformation of the entire rod.
In the case of a member with a variable cross-section, the strain is not constant but depends on the position. The deformation of an...
471
Deformation in a Circular Shaft01:10

Deformation in a Circular Shaft

One of the distinctive characteristics of circular shafts is their ability to maintain their cross-sectional integrity under torsion. In other words, each cross-section continues to exist as a flat, unaltered entity, simply rotating like a solid, rigid slab. To understand the distribution of shearing stress within such a shaft, consider a cylindrical section inside this circular shaft. This section has a length of L and a radius of R, with one end fixed. The radius of the cylindrical section is...
919