Related Experiment Video

Updated: Jan 29, 2026

Versatile Technique to Produce a Hierarchical Design in Nanoporous Gold
05:28

Versatile Technique to Produce a Hierarchical Design in Nanoporous Gold

Published on: February 10, 2023

2.1K

Deformation Induced Hierarchical Twinning Coupled with Omega Transformation in a Metastable β-Ti Alloy

S A Mantri1, F Sun2, D Choudhuri1

  • 1Department of Mater Science and Engineering, University of North Texas, Denton, TX, 76207, USA.

Scientific Reports
|February 6, 2019
PubMed

More Related Videos

An Available Technique for Preparation of New Cast MnCuNiFeZnAl Alloy with Superior Damping Capacity and High Service Temperature14:51

An Available Technique for Preparation of New Cast MnCuNiFeZnAl Alloy with Superior Damping Capacity and High Service Temperature

Published on: September 23, 2018

7.4K
Molecular Analysis of Endothelial-mesenchymal Transition Induced by Transforming Growth Factor-β Signaling07:49

Molecular Analysis of Endothelial-mesenchymal Transition Induced by Transforming Growth Factor-β Signaling

Published on: August 3, 2018

11.8K

Related Concept Videos

Bacterial Transformation01:33

Bacterial Transformation

In 1928, bacteriologist Frederick Griffith worked on a vaccine for pneumonia, which is caused by Streptococcus pneumoniae bacteria. Griffith studied two pneumonia strains in mice: one pathogenic and one non-pathogenic. Only the pathogenic strain killed host mice.
Griffith made an unexpected discovery when he killed the pathogenic strain and mixed its remains with the live, non-pathogenic strain. Not only did the mixture kill host mice, but it also contained living pathogenic bacteria that...
59.8K
Plastic Deformations01:19

Plastic Deformations

Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their...
459
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
431
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
390
Deformations in a Symmetric Member in Bending01:18

Deformations in a Symmetric Member in Bending

When analyzing the deformation of a symmetric prismatic member subjected to bending by equal and opposite couples, it becomes clear that as the member bends, the originally straight lines on its wider faces curve into circular arcs, with a constant radius centered at a point known as Point C. This phenomenon helps to understand the stress and strain distribution within the member more clearly.
When the member is segmented into tiny cubic elements, it is observed that the primary stress...
514
Deformation of Member under Multiple Loadings01:11

Deformation of Member under Multiple Loadings

When a rod is made of different materials or has various cross-sections, it must be divided into parts that meet the necessary conditions for determining the deformation. These parts are each characterized by their internal force, cross-sectional area, length, and modulus of elasticity. These parameters are then used to compute the deformation of the entire rod.
In the case of a member with a variable cross-section, the strain is not constant but depends on the position. The deformation of an...
471