Related Experiment Video

Updated: Jan 29, 2026

Full-field Strain Measurements for Microstructurally Small Fatigue Crack Propagation Using Digital Image Correlation Method
07:37

Full-field Strain Measurements for Microstructurally Small Fatigue Crack Propagation Using Digital Image Correlation Method

Published on: January 16, 2019

10.1K

Full-field Strain Measurements for Microstructurally Small Fatigue Crack Propagation Using Digital Image Correlation

Evgenii Malitckii1, Heikki Remes2, Pauli Lehto2

  • 1Department of Mechanical Engineering, Aalto University School of Engineering; evgeny.malitskiy@aalto.fi.

Journal of Visualized Experiments : Jove
|February 9, 2019
PubMed

More Related Videos

Crack Monitoring in Resonance Fatigue Testing of Welded Specimens Using Digital Image Correlation05:30

Crack Monitoring in Resonance Fatigue Testing of Welded Specimens Using Digital Image Correlation

Published on: September 29, 2019

8.7K
Measuring Local Tissue Strains in Tendons via Open-Source Digital Image Correlation07:50

Measuring Local Tissue Strains in Tendons via Open-Source Digital Image Correlation

Published on: January 27, 2023

3.6K

Related Concept Videos

Measurements of Strain01:27

Measurements of Strain

Strain quantifies the deformation of a material under force, typically measured as normal strain, which represents the change in length when compared with the original length. Electrical strain gauges are used for enhanced accuracy. These devices consist of a conductive wire mounted on a paper backing that adheres to the material's surface. These gauges operate on the piezoresistive effect, where the wire's electrical resistance changes in response to mechanical deformation. The strain...
2.6K
Correlations02:20

Correlations

Correlation means that there is a relationship between two or more variables (such as ice cream consumption and crime), but this relationship does not necessarily imply cause and effect. When two variables are correlated, it simply means that as one variable changes, so does the other. We can measure correlation by calculating a statistic known as a correlation coefficient. A correlation coefficient is a number from -1 to +1 that indicates the strength and direction of the relationship between...
35.9K
Fatigue01:21

Fatigue

Fatigue occurs when materials rupture under repeated or fluctuating loads, even at stress levels far below their static breaking strength. It typically results in brittle failure, even for ductile materials. It is a critical consideration in designing machines and structural components subjected to repetitive or varying loads. The nature of these loadings can range from fluctuating loads like unbalanced pump impellers causing vibrations to repeatedly bending a thin steel rod wire back and forth...
833
Correlation and Causation01:27

Correlation and Causation

Statistical tests can calculate whether there is a relationship, or correlation, between independent and dependent variables. An indirect relationship of the variables signifies a correlation, while a direct relationship shows causation. If it is determined that no connection exists between the variables, then the correlation is a coincidence.
Correlation versus Causation
If the dependent variable increases or decreases when the independent variable increases, there is a positive or negative...
42.5K
Correlation01:09

Correlation

In statistics, two variables are said to be correlated if the values of one variable are associated with the other variable. Depending on the relationship between two variables, correlation can be of three types– positive correlation, negative correlation, and zero correlation.
Two variables, for example, a and b, are said to be positively correlated if both variables move in the same direction. In other words, a positive correlation exists between two variables, a and b, if:
15.1K
Types of Non-structural Cracks in Concrete01:28

Types of Non-structural Cracks in Concrete

Non-structural cracks are primarily of three types: plastic, early-age thermal, and drying shrinkage cracks. Plastic cracks are further classified into plastic shrinkage cracks and plastic settlement cracks.
Plastic shrinkage cracks typically form within hours after the concrete is poured. The concrete's surface dries faster than the bottom, creating tensile stress that the still-plastic concrete cannot withstand, leading to diagonal or randomly patterned cracks on the concrete surface.
505