Related Experiment Video

Updated: Jan 29, 2026

Flame Experiments at the Advanced Light Source: New Insights into Soot Formation Processes
10:04

Flame Experiments at the Advanced Light Source: New Insights into Soot Formation Processes

Published on: May 26, 2014

13.3K

Enhanced emissions of brominated flame retardants from indoor sources by direct contact with dust

Zhuxiu Qian1, Yiwen Xu1, Chaofan Zheng1

  • 1International Joint Research Center for Persistent Toxic Substances, College of Environment, Zhejiang University of Technology, Hangzhou, 310014, China.

Environmental Monitoring and Assessment
|February 20, 2019
PubMed

Keywords:
Direct contactDust coverageEmissionIndoor materialsParticle sizes

More Related Videos

Experimental Methods of Dust Charging and Mobilization on Surfaces with Exposure to Ultraviolet Radiation or Plasmas07:54

Experimental Methods of Dust Charging and Mobilization on Surfaces with Exposure to Ultraviolet Radiation or Plasmas

Published on: April 3, 2018

8.7K
Design and Use of a Full Flow Sampling System FFS for the Quantification of Methane Emissions08:18

Design and Use of a Full Flow Sampling System FFS for the Quantification of Methane Emissions

Published on: June 12, 2016

17.3K

Related Concept Videos

Retarders01:19

Retarders

Retarders are chemical admixtures designed to extend the setting time, which is especially useful when there is a delay in sequential concrete pours to prevent cold joints and to achieve a cohesive structure. Retarders, when used in appropriate amounts, can also enhance the architectural appearance of exposed aggregate finishes.
The function of retarders is to delay the setting of concrete, and this effect can be measured using a penetration test. The retardation process involves adding...
264
Emission Spectra02:39

Emission Spectra

When solids, liquids, or condensed gases are heated sufficiently, they radiate some of the excess energy as light. Photons produced in this manner have a range of energies, and thereby produce a continuous spectrum in which an unbroken series of wavelengths is present.
76.2K
Flame Photometry: Overview01:02

Flame Photometry: Overview

Flame photometry, also known as flame emission spectrometry, is a technique used for the qualitative and quantitative analysis of elements present in a sample using a flame as the source of excitation energy. The concept of flame photometry was realized in the early 1860s by Kirchhoff and Bunsen, who discovered that specific elements emit characteristic radiation when excited in flames. The first instrument developed for this purpose was used to measure sodium (Na) in plant ash using a Bunsen...
1.5K
Flame Photometry: Lab01:16

Flame Photometry: Lab

In a flame photometer, when a solution like potassium chloride is aspirated into the flame, the solvent evaporates, leaving behind dehydrated salt. This salt dissociates into free gaseous atoms in their ground state. Some of these atoms absorb energy from the flame, leading to their excitation. The excited atoms return to the ground state, emitting photons at characteristic wavelengths. Because only electronic transitions are involved, the resulting emission lines are very narrow. The intensity...
934
Radical Substitution: Allylic Bromination01:27

Radical Substitution: Allylic Bromination

In organic synthesis, the formation of products can be altered by changing the reaction conditions. For example, a dibromo addition product is formed when propene is treated with bromine at room temperature. In contrast, propene undergoes allylic substitution in non-polar solvents at high temperatures to give 3-bromopropene. In order to avoid the addition reaction, the bromine concentration must be kept as low as possible throughout the reaction. This can be achieved using N-bromosuccinimide...
6.6K
Contact Angle01:13

Contact Angle

When a solid is dipped inside a liquid, the liquid surface becomes curved near the contact. For some solid–liquid interfaces, the liquid is pulled up along the solid, while for others, the liquid surface is convex or depressed near the solid surface. This phenomenon can be explained using the concept of cohesive and adhesive forces.
The adhesive force is the molecular force between molecules of different materials, that is, between the molecules of the solid and the liquid. The cohesive...
19.0K