Related Experiment Video

Updated: Jan 28, 2026

MRI and PET in Mouse Models of Myocardial Infarction
10:46

MRI and PET in Mouse Models of Myocardial Infarction

Published on: December 19, 2013

12.4K

How to detect and correct myocardial creep in myocardial perfusion imaging using Rubidium-82 PET?

S S Koenders1,2, J D van Dijk3, P L Jager3

  • 1Department of Nuclear Medicine, Isala hospital, PO Box 10400, 8000 GK, Zwolle, The Netherlands. skoenders93@gmail.com.

Journal of Nuclear Cardiology : Official Publication of the American Society of Nuclear Cardiology
|February 22, 2019
PubMed

Keywords:
82RbMyocardial blood flowPET myocardial perfusion imagingmyocardial creeppharmacological vasodilators

More Related Videos

Induction of Myocardial Infarction and Myocardial Ischemia-Reperfusion Injury in Mice08:28

Induction of Myocardial Infarction and Myocardial Ischemia-Reperfusion Injury in Mice

Published on: January 19, 2022

8.2K
Ultrasonic Assessment of Myocardial Microstructure10:53

Ultrasonic Assessment of Myocardial Microstructure

Published on: January 14, 2014

5.8K

Related Concept Videos

Creep in Concrete01:22

Creep in Concrete

Creep refers to the time-dependent increase in strain under a sustained load, excluding other time-dependent deformations associated with shrinkage, swelling, and thermal expansion in concrete. The primary mechanism behind creep involves the loss of physically adsorbed water from the calcium silicate hydrate within the hydrated cement paste. This process is further exacerbated by concrete's non-linear stress-strain relationship, microcrack development in the interfacial transition zone, and...
1.2K
Factors Affecting Creep01:28

Factors Affecting Creep

In normal-weight aggregate concrete, the hardened cement paste is the primary contributor to creep, whereas the aggregates, being stiffer than the cement paste, are more resilient to stress-induced deformation. The stiffness of the aggregates is defined by their modulus of elasticity, and the more voluminous they are in the concrete, the less it will creep.
Further, the water/cement ratio is critical, as a lower ratio increases concrete strength, thus reducing creep. The strength of the...
452
Effects of Creep01:25

Effects of Creep

Creep in concrete, the gradual deformation under prolonged stress, significantly impacts the integrity of structures. For reinforced concrete beams, it can be a vital design consideration, as it increases deflection, sometimes necessitating additional design measures. In columns, especially slender ones under eccentric loads, creep can cause buckling, compromising their stability. However, creep can be beneficial in indeterminate structures by mitigating stresses that arise from shrinkage,...
437
Distance Corrections01:15

Distance Corrections

To achieve precise distance measurements, especially in surveying and construction, certain corrections must be applied to account for potential sources of error like the standardization errors, temperature variations, and slope adjustments.Standardization error emerges when measurement equipment undergoes changes, such as wear, repairs, or weather impacts. To address this, surveyors compare the equipment’s readings to a standard. This process identifies any deviation that might lead to...
282
Power Factor Correction01:20

Power Factor Correction

The power transmission to a factory involves the transfer of apparent power, a combination of active and reactive power. The power factor measures how effectively electrical power is converted into useful work output. The ratio of the real power (KW) that does the work to the apparent power (KVA) supplied to the circuit.
532
NMR Spectrometers: Resolution and Error Correction01:14

NMR Spectrometers: Resolution and Error Correction

When magnetic nuclei in a sample achieve resonance and undergo relaxation, the signal detected in NMR is an approximately exponential free induction decay. Fourier transform of an exponential decay yields a Lorentzian peak in the frequency domain. Lorentzian peaks in an NMR spectrum are defined by their amplitude, full width at half maximum, and position, where the peak width is governed by the spin-spin relaxation time alone. In real experiments, however, the applied magnetic field is rendered...
1.1K