Related Experiment Video

Updated: Jan 28, 2026

Measurements of Local Instantaneous Convective Heat Transfer in a Pipe - Single and Two-phase Flow
08:25

Measurements of Local Instantaneous Convective Heat Transfer in a Pipe - Single and Two-phase Flow

Published on: April 30, 2018

7.6K

Experimental characterization of an n-pentane oscillating heat pipe for waste heat recovery in ventilation systems

Govinda Mahajan1, Scott M Thompson2, Heejin Cho3

  • 1Rheem Manufacturing, 2600 Gunter Park Dr., Montgomery, AL, 36109, USA.

Heliyon
|March 7, 2019
PubMed

Keywords:
EnergyMechanical engineering

More Related Videos

A Preclinical Model of Exertional Heat Stroke in Mice08:22

A Preclinical Model of Exertional Heat Stroke in Mice

Published on: July 1, 2021

4.3K
Thermal Limits Determination for Zooplankton Using a Heat Block07:16

Thermal Limits Determination for Zooplankton Using a Heat Block

Published on: November 18, 2022

1.7K

Related Concept Videos

Quantifying Heat02:46

Quantifying Heat

Thermal Energy Microscopically, thermal energy is the kinetic energy associated with the random motion of atoms and molecules. Temperature is a quantitative measure of “hot” or “cold”, which depends on the amount of thermal energy. When the atoms and molecules in an object are moving or vibrating quickly, they have a higher average kinetic energy (KE) (or higher thermal energy), and the object is perceived as “hot”, or it is described as being at a higher temperature. When the...
62.0K
Specific Heat01:16

Specific Heat

The specific heat capacity of a substance refers to the energy required to increase the temperature of one gram of that substance by one degree Celcius. Specific heat capacity is often represented in calories (cal), grams (g), and degrees Celsius (oC), but can also be expressed in joules (J), kilograms (kg), and Kelvin (K), among other units.
For example, increasing the temperature of one gram of water by 1°C requires one calorie of heat energy and can be written as 1 cal/g-°C, or...
67.4K
Heat Flow and Specific Heat01:12

Heat Flow and Specific Heat

Heat is a type of energy transfer that is caused by a temperature difference, and it can change the temperature of an object. Since heat is a form of energy, its SI unit is the joule (J). Another common unit of energy often used for heat is the calorie (cal), which is defined as the energy needed to change the temperature of 1 g of water by 1 °C, specifically between 14.5 °C and 15.5 °C, since the energy needed shows a slight temperature dependence. Another commonly used unit is...
6.8K
Heating and Cooling Curves02:44

Heating and Cooling Curves

When a substance—isolated from its environment—is subjected to heat changes, corresponding changes in temperature and phase of the substance is observed; this is graphically represented by heating and cooling curves.
For instance, the addition of heat raises the temperature of a solid; the amount of heat absorbed depends on the heat capacity of the solid (q = mcsolidΔT). According to thermochemistry, the relation between the amount of heat absorbed or released by a substance, q, and its...
27.6K
Heat and Free Expansion01:24

Heat and Free Expansion

The work done by a thermodynamic system depends not only on the initial and final states but also on the intermediate states—that is, on the path. Like work, when heat is added to a thermodynamic system, it undergoes a change of state, and the state attained depends on the path from the initial state to the final state. Consider an ideal gas cylinder fitted with a piston. When the cylinder is heated at a constant temperature, the gas molecules absorb energy and expand slowly in a...
2.9K
Single Pipe Systems01:24

Single Pipe Systems

In pipe flow analysis, problems are typically categorized into three types — Type I, Type II, and Type III — based on the known parameters and the desired outcome. Each type of problem addresses specific engineering requirements using fluid properties, pipe characteristics, and operational conditions.
In a Type I problem, fluid properties (density and viscosity), pipe characteristics (including diameter, length, and surface roughness), and the flow rate or average velocity are...
446