Deformed Wing Virus Infection in Honey Bees (Apis mellifera L.)

Roman V Koziy1, Sarah C Wood1, Ivanna V Kozii1

  • 11 Western College of Veterinary Medicine, University of Saskatchewan, Saskatoon, Saskatchewan, Canada.

Veterinary Pathology
|March 13, 2019
PubMed

Insights

Deformed wing virus (DWV) in honey bees (Apis mellifera) causes prolonged emergence and higher mortality. DWV infection also leads to hypoplasia of hypopharyngeal and mandibular glands in newly emerged workers.

Area of Science:

  • Veterinary Pathology
  • Apiculture Science
  • Insect Virology

Background:

  • Deformed wing virus (DWV) is a significant pathogen impacting honey bee (Apis mellifera) health globally.
  • DWV is transmitted by the parasitic Varroa destructor mite.
  • The pathological mechanisms underlying DWV infection require further elucidation.

Purpose of the Study:

  • To investigate the clinicopathological and histological features of natural DWV infection in worker honey bees.
  • To correlate DWV infection severity with observed pathological changes and viral load.

Main Methods:

  • Observation of worker honey bee emergence in five DWV-affected colonies.
  • Histopathological examination of newly emerged worker honey bees.
  • Quantification of DWV load in affected and unaffected worker bees.

Main Results:

  • DWV-affected bees exhibited a 2-fold delay in emergence and 30% higher mortality.
  • Hypopharyngeal glands showed hypoplasia and increased apoptosis in DWV-infected bees.
  • Mandibular glands were hypoplastic with cuboidal epithelium in severely affected bees.
  • DWV load was significantly higher (1.7 x 10^6 times) in severely affected workers.

Conclusions:

  • DWV infection is linked to delayed emergence and increased mortality in honey bees.
  • Histological damage to hypopharyngeal and mandibular glands is a key feature of DWV pathology.
  • DWV significantly impacts honey bee development and gland morphology, beyond wing deformities.

Related Concept Videos

Plastic Deformations01:19

Plastic Deformations

Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their...
452
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
428
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
387
Deformations in a Symmetric Member in Bending01:18

Deformations in a Symmetric Member in Bending

When analyzing the deformation of a symmetric prismatic member subjected to bending by equal and opposite couples, it becomes clear that as the member bends, the originally straight lines on its wider faces curve into circular arcs, with a constant radius centered at a point known as Point C. This phenomenon helps to understand the stress and strain distribution within the member more clearly.
When the member is segmented into tiny cubic elements, it is observed that the primary stress...
511
What are Viruses?00:50

What are Viruses?

Overview
128.0K
Deformation of Member under Multiple Loadings01:11

Deformation of Member under Multiple Loadings

When a rod is made of different materials or has various cross-sections, it must be divided into parts that meet the necessary conditions for determining the deformation. These parts are each characterized by their internal force, cross-sectional area, length, and modulus of elasticity. These parameters are then used to compute the deformation of the entire rod.
In the case of a member with a variable cross-section, the strain is not constant but depends on the position. The deformation of an...
465