Related Experiment Video

Updated: Jan 27, 2026

Probe-based Real-time PCR Approaches for Quantitative Measurement of microRNAs
10:28

Probe-based Real-time PCR Approaches for Quantitative Measurement of microRNAs

Published on: April 14, 2015

33.8K

DOA Estimation of Unknown Emitter Signal Based on Time Reversal and Coprime Array

Bing Li1,2, Shiqi Liu3, Deshuang Zhao2

  • 1School of Electrical Engineering, Southwest Jiaotong University, Chengdu 610031, China. bllijess@outlook.com.

Sensors (Basel, Switzerland)
|March 24, 2019
PubMed

Keywords:
coprime arraydirection-of-arrivallow signal-to-noise ratiomultipathnoise suppressiontime reversal

More Related Videos

P300-Based Brain-Computer Interface Speller Performance Estimation with Classifier-Based Latency Estimation06:09

P300-Based Brain-Computer Interface Speller Performance Estimation with Classifier-Based Latency Estimation

Published on: September 8, 2023

939
Scale-up Chemical Synthesis of Thermally-activated Delayed Fluorescence Emitters Based on the Dibenzothiophene-S,S-Dioxide Core08:51

Scale-up Chemical Synthesis of Thermally-activated Delayed Fluorescence Emitters Based on the Dibenzothiophene-S,S-Dioxide Core

Published on: October 24, 2017

10.1K

Related Concept Videos

Estimating Population Mean with Unknown Standard Deviation01:22

Estimating Population Mean with Unknown Standard Deviation

In practice, we rarely know the population standard deviation. In the past, when the sample size was large, this did not present a problem to statisticians. They used the sample standard deviation s as an estimate for σ and proceeded as before to calculate a confidence interval with close enough results. However, statisticians ran into problems when the sample size was small. A small sample size caused inaccuracies in the confidence interval.
William S. Gosset (1876–1937) of the...
8.8K
Basic Continuous Time Signals01:22

Basic Continuous Time Signals

Basic continuous-time signals include the unit step function, unit impulse function, and unit ramp function, collectively referred to as singularity functions. Singularity functions are characterized by discontinuities or discontinuous derivatives.
The unit step function, denoted u(t), is zero for negative time values and one for positive time values, exhibiting a discontinuity at t=0. This function often represents abrupt changes, such as the step voltage introduced when turning a car's...
674
Basic Discrete Time Signals01:16

Basic Discrete Time Signals

The unit step sequence is defined as 1 for zero and positive values of the integer n. This sequence can be graphically displayed using a set of eight sample points, showing a step function starting from n=0 and remaining constant thereafter.
The unit impulse or sample sequence is mathematically expressed as zero for all n values except at n=0, where it is one. The unit impulse sequence, denoted by δ(n), is the first difference of the unit step sequence, while the unit step sequence u(n) is the...
693
Sampling Continuous Time Signal01:11

Sampling Continuous Time Signal

In signal processing, a continuous-time signal can be sampled using an impulse-train sampling technique, followed by the zero-order hold method. Impulse-train sampling involves the use of a periodic impulse train, which consists of a series of delta functions spaced at regular intervals determined by the sampling period. When a continuous-time signal is multiplied by this impulse train, it generates impulses with amplitudes corresponding to the signal's values at the sampling points.
In the...
712
Testing a Claim about Mean: Unknown Population SD01:21

Testing a Claim about Mean: Unknown Population SD

A complete procedure of testing a hypothesis about a population mean when the population standard deviation is unknown is explained here.
Estimating a population mean requires the samples to be approximately normally distributed. The data should be collected from the randomly selected samples having no sampling bias. There is no specific requirement for sample size. But if the sample size is less than 30, and we don't know the population standard deviation, a different approach is used;...
5.7K
What are Estimates?01:06

What are Estimates?

It isn't easy to measure a parameter such as the mean height or the mean weight of a population. So, we draw samples from the population and calculate the mean height or mean weight of the individuals in the sample. This sample data acts as a representative measure of the population parameter. These sample statistics are known as estimates. 
The estimate for the mean of a sample is denoted by ͞x, whereas the mean of the population is designated as μ. Further, parameters such...
8.2K