Related Experiment Video

Updated: Jan 26, 2026

Robotic Cochlear Implantation for Direct Cochlear Access
08:06

Robotic Cochlear Implantation for Direct Cochlear Access

Published on: June 16, 2022

4.0K

Maximum preimplantation monosyllabic score as predictor of cochlear implant outcome

Ulrich Hoppe1, Thomas Hocke2, Anne Hast3

  • 1Audiologische Abteilung, Hals-Nasen-Ohrenklinik, Kopf- und Halschirurgie, Universitätsklinikum Erlangen, Waldstr. 1, 91054, Erlangen, Germany. ulrich.hoppe@uk-erlangen.de.

HNO
|April 5, 2019
PubMed
Abstract

Keywords:
Cochlear implantsHearing lossHearing testsSpeech audiometrySpeech discrimination tests

More Related Videos

Electrically Evoked Stapedius Reflex Measurements in Cochlear Implantation and Its Application in the Postoperative Fitting Process07:00

Electrically Evoked Stapedius Reflex Measurements in Cochlear Implantation and Its Application in the Postoperative Fitting Process

Published on: June 21, 2024

1.5K
Cochlear Implantation in the Guinea Pig09:56

Cochlear Implantation in the Guinea Pig

Published on: June 15, 2018

11.8K

Related Concept Videos

Maximum Deflection01:13

Maximum Deflection

When analyzing beams under unsymmetrical loads, such as a train moving on a bridge, it is crucial to accurately determine the points of maximum stress and deflection. The process involves identifying the maximum deflection of the beam, which may not always occur at its midpoint due to the uneven distribution of the load.
The maximum deflection occurs at a specific point, known as point O, where the tangent to the deflection curve is horizontal. To find point O, the slope of the tangent at any...
1.0K
Maximum Power Transfer01:16

Maximum Power Transfer

Numerous practical applications within engineering disciplines, such as telecommunications, necessitate optimizing power delivery to a connected load. This pursuit, however, entails inherent internal losses, which can either equal or exceed the power supplied to the load. The Thevenin equivalent circuit is helpful in finding the maximum power a linear circuit can deliver to a load. It is assumed in this context that the load resistance can be adjusted.
By substituting the entire circuit with...
869
Maximum Size of Aggregate01:12

Maximum Size of Aggregate

The maximum size of aggregate is defined as the aperture of the sieve retaining 15 percent or more of the particles present in the aggregate sample. The aggregate's maximum size impacts the concrete's water requirement, workability, and strength. Larger aggregates reduce the surface area needing cement paste coverage, which can lower water needs, thereby allowing a decrease in the water-to-cement ratio when the desired workability and richness of the mix are to be maintained, which can...
537
The Maximum Power Transfer Theorem01:20

The Maximum Power Transfer Theorem

Consider a linear AC Thevenin equivalent circuit connected to a load impedance.
The load connected draws the current, and the circuit delivers the power to the load. The alternating current flowing through the load is determined using the rectangular form of voltages, currents, network impedance, and load impedance. The average power delivered to the load is obtained from the product of the square of current and load resistance.
1.2K
Introduction to z Scores01:06

Introduction to z Scores

A z score (or standardized value) is measured in units of the standard deviation. It tells you how many standard deviations the value x is above (to the right of) or below (to the left of) the mean, μ. Values of x that are larger than the mean have positive z scores, and values of x that are smaller than the mean have negative z scores. If x equals the mean, then x has a zero z score. It is important to note that the mean of the z scores is zero, and the standard deviation is one.
z scores...
11.0K
Introduction to z Scores01:05

Introduction to z Scores

A z score (or standardized value) is measured in units of the standard deviation. It indicates how many standard deviations the value x is above (to the right of) or below (to the left of) the mean, μ. Values of x that are larger than the mean have positive z scores, and values of x that are smaller than the mean have negative z scores. If x equals the mean, then x has a zero z score. It is important to note that the mean of the z scores is zero, and the standard deviation is one.
z scores...
1.3K