Related Experiment Video

Updated: Jan 26, 2026

Supercritical Nitrogen Processing for the Purification of Reactive Porous Materials
09:05

Supercritical Nitrogen Processing for the Purification of Reactive Porous Materials

Published on: May 15, 2015

15.3K

Peel and Penetration Resistance of Porous Polyethylene Terephthalate Material Produced by CO₂-Assisted Polymer

Takafumi Aizawa1

  • 1Research Institute for Chemical Process Technology, National Institute of Advanced Industrial Science and Technology, 4-2-1 Nigatake, Miyagino-ku, Sendai 983-8551, Japan. t.aizawa@aist.go.jp.

Molecules (Basel, Switzerland)
|April 12, 2019
PubMed

Keywords:
CO2-assisted polymer compressioncross-sectional modelpeel resistancepenetration resistancepolyethylene terephthalateporous polymer

More Related Videos

Procedure for the Transfer of Polymer Films Onto Porous Substrates with Minimized Defects05:02

Procedure for the Transfer of Polymer Films Onto Porous Substrates with Minimized Defects

Published on: June 22, 2019

7.1K
Preparation of Highly Porous Coordination Polymer Coatings on Macroporous Polymer Monoliths for Enhanced Enrichment of Phosphopeptides10:27

Preparation of Highly Porous Coordination Polymer Coatings on Macroporous Polymer Monoliths for Enhanced Enrichment of Phosphopeptides

Published on: July 14, 2015

10.5K

Related Concept Videos

Polymers02:34

Polymers

The word polymer is derived from the Greek words “poly” which means “many” and “mer” which means “parts”. Polymers are long chains of molecules composed of repeating units of smaller molecules, known as monomers. They either occur naturally, such as DNA and proteins, or can be constructed synthetically, like plastics. They have varied structural characteristics, such as linear chains, branched chains, or complex networks, that contribute to the...
40.6K
Polymers02:34

Polymers

23.2K
Resistivity01:22

Resistivity

When a voltage is applied to a conductor, an electrical field is generated, and charges in the conductor feel the force due to the electrical field. The current density that results depends on the electrical field and the properties of the material. In some materials, including metals at a given temperature, the current density is approximately proportional to the electrical field. In these cases, the current density can be modeled as:
4.4K
Resistance01:19

Resistance

When a current moves through any conductor, the conductor causes some level of difficulty for the current to flow. The measure of that difficulty is known as the resistance of the material and is represented by R. Every material has its own resistance. In the case of conductors, heat is emitted whenever a current passes through them. Resistance depends on the resistivity of the material. Resistivity is a characteristic of the material used to fabricate electrical components, whereas the...
5.7K
Behavior of Concrete Under Compressive Load01:23

Behavior of Concrete Under Compressive Load

Concrete exhibits specific behaviors under different compressive loads. Understanding this is crucial for understanding its structural integrity. When concrete undergoes uniaxial compression, it tends to develop cracks that run parallel to the direction of the force. These parallel cracks stem from localized tensile stresses that occur perpendicular to the compression direction. Additionally, angled cracks may appear due to the formation of shear planes.
As the concrete specimen fractures under...
618
Members Made of Elastoplastic Material01:19

Members Made of Elastoplastic Material

The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
As the bending moment...
384