Related Experiment Video

Updated: Jan 26, 2026

C-arm-Free Simultaneous OLIF51 and Percutaneous Pedicle Screw Fixation in a Single Lateral Position

C-arm-Free Simultaneous OLIF51 and Percutaneous Pedicle Screw Fixation in a Single Lateral Position

Published on: September 16, 2022

Biomechanical Analysis of Cortical Versus Pedicle Screw Fixation Stability in TLIF, PLIF, and XLIF Applications

Edward K Nomoto¹, Guy R Fogel², Alexandre Rasouli¹

¹Cedars-Sinai Spine Center, Los Angeles, CA, USA.

Global Spine Journal

|April 16, 2019

Abstract

Study Design:

Cadaveric biomechanical study.

Objectives:

Medial-to-lateral trajectory cortical screws are of clinical interest due to the ability to place them through a less disruptive, medialized exposure compared with conventional pedicle screws. In this study, cortical and pedicle screw trajectory stability was investigated in single-level transforaminal lumbar interbody fusion (TLIF), posterior lumbar interbody fusion (PLIF), and extreme lateral interbody fusion (XLIF) constructs.

Methods:

Eight lumbar spinal units were used for each interbody/screw trajectory combination. The following constructs were tested: TLIF + unilateral facetectomy (UF) + bilateral pedicle screws (BPS), TLIF + UF + bilateral cortical screws (BCS), PLIF + medial facetectomy (MF) + BPS, PLIF + bilateral facetectomy (BF) + BPS, PLIF + MF + BCS, PLIF + BF + BCS, XLIF + BPS, XLIF + BCS, and XLIF + bilateral laminotomy + BCS. Range of motion (ROM) in flexion-extension, lateral bending, and axial rotation was assessed using pure moments.

Results:

All instrumented constructs were significantly more rigid than intact (P < .05) in all test directions except TLIF + UF + BCS, PLIF + MF + BCS, and PLIF + BF + BCS in axial rotation. In general, XLIF and PLIF + MF constructs were more rigid (lowest ROM) than TLIF + UF and PLIF + BF constructs. In the presence of substantial iatrogenic destabilization (TLIF + UF and PLIF + BF), cortical screw constructs tended to be less rigid (higher ROM) than the same pedicle screw constructs in lateral bending and axial rotation; however, no statistically significant differences were found when comparing pedicle and cortical fixation for the same interbody procedures.

Conclusions:

Both cortical and pedicle trajectory screw fixation provided stability to the 1-level interbody constructs. Constructs with the least iatrogenic destabilization were most rigid. The more destabilized constructs showed less lateral bending and axial rotation rigidity with cortical screws compared with pedicle screws. Further investigation is warranted to understand the clinical implications of differences between constructs.

Keywords:

cortical screw lumbar interbody fusion screw fixation screw trajectory

More Related Videos

A Spine Robotic-Assisted Navigation System for Pedicle Screw Placement

A Spine Robotic-Assisted Navigation System for Pedicle Screw Placement

Published on: May 11, 2020

Pedicle Screw Placement Using an Augmented Reality Head-Mounted Display in a Porcine Model

Pedicle Screw Placement Using an Augmented Reality Head-Mounted Display in a Porcine Model

Published on: May 24, 2024

Related Concept Videos

Self-Locking Screw

Self-Locking Screw

A square-threaded screw jack is a mechanical device widely used for lifting heavy loads or applying considerable force. One of the key features that can make a screw jack more effective and reliable is its self-locking capability.
A square-threaded screw jack carrying a load is considered self-locking if the screw retains its position even after the moment applied to it is removed.

Screw: Problem Solving

Screw: Problem Solving

In mechanical engineering, the interaction between a threaded screw shaft and a plate gear involves analyzing the resisting torque on the plate gear that can be overpowered when a specific torsional moment is applied to the shaft. To better comprehend this concept, consider a generic situation with a threaded screw shaft with a given mean radius and lead and a plate gear with a specified mean radius. The coefficient of static friction between the screw and gear is also provided.
To evaluate the...

Frictional Forces on Screws

Frictional Forces on Screws

Screws are characterized by a helical ridge known as a thread wrapped around a cylindrical shaft. They are commonly used as fasteners to hold objects together or to transmit power and motion in machines. One type of screw that is particularly useful for transmitting power is the square-threaded screw.
A jack with a square-threaded screw is a mechanical device used to lift heavy loads by applying a force at its handle. When the force is applied, the screw turns, raising the load. The screw can...

Nuclear Stability

Nuclear Stability

Protons and neutrons, collectively called nucleons, are packed together tightly in a nucleus. With a radius of about 10−15 meters, a nucleus is quite small compared to the radius of the entire atom, which is about 10−10 meters. Nuclei are extremely dense compared to bulk matter, averaging 1.8 × 1014 grams per cubic centimeter. If the earth’s density were equal to the average nuclear density, the earth’s radius would be only about 200 meters.
To hold positively charged protons together...

RNA Stability

RNA Stability

Intact DNA strands can be found in fossils, while scientists sometimes struggle to keep RNA intact under laboratory conditions. The structural variations between RNA and DNA underlie the differences in their stability and longevity. Because DNA is double-stranded, it is inherently more stable. The single-stranded structure of RNA is less stable but also more flexible and can form weak internal bonds. Additionally, most RNAs in the cell are relatively short, while DNA can be up to 250 million...

Fixation and Sectioning

Fixation and Sectioning

Two basic types of preparation are used to visualize specimens with a light microscope: wet mounts and fixed specimens.
The simplest type of preparation is the wet mount, in which the specimen is placed in a drop of liquid on the slide. A liquid specimen can be directly deposited on the slide using a dropper. Solid specimens, such as skin scraping, can be placed on the slide before adding a drop of liquid to prepare the wet mount. Sometimes the liquid is simply water, but stains are often added...

Articles linked to this work by shared authors, journal, and citation graph.

Restorative neurostimulation outcomes for mechanical chronic low back pain: delayed-start crossover from optimal medical management and 2-year treatment longitudinal analyses from the RESTORE randomized controlled trial.

The spine journal : official journal of the North American Spine Society·2026

Restorative Neurostimulation Therapy Compared to Optimal Medical Management: A Randomized Evaluation (RESTORE) for the Treatment of Chronic Mechanical Low Back Pain due to Multifidus Dysfunction.

Pain and therapy·2025

Multirod posterior occipitocervical instrumentation constructs: a biomechanical analysis and initial case series of 10 patients with complex craniocervical pathology.

The spine journal : official journal of the North American Spine Society·2024

Complications Have Not Improved With Newer Generation Robots.

Global spine journal·2023

Biomechanical Evaluation of Transforaminal Lumbar Interbody Fusion with Coflex-F and Pedicle Screw Fixation: Finite Element Analysis of Static and Vibration Conditions.

Orthopaedic surgery·2022

Novel use of robotics and navigation for anterior lumbar total disc replacement surgery.

North American Spine Society journal·2022

See all related articles