Related Experiment Video

Updated: Jan 24, 2026

Induction of Mesenchymal-Epithelial Transitions in Sarcoma Cells
11:42

Induction of Mesenchymal-Epithelial Transitions in Sarcoma Cells

Published on: April 7, 2017

9.8K

Epithelial-Mesenchymal Plasticity in Organotropism Metastasis and Tumor Immune Escape

Xiang Nan1,2, Jiang Wang3, Haowen Nikola Liu4

  • 1Center for Biomedical Engineering, University of Science and Technology of China, Hefei 230052, China. xnan2@houstonmethodist.org.

Journal of Clinical Medicine
|May 28, 2019
PubMed

Keywords:
EMT heterogeneitycell–cell communicationorganotropism metastasistumor immune escape

More Related Videos

Induction and Analysis of Epithelial to Mesenchymal Transition10:37

Induction and Analysis of Epithelial to Mesenchymal Transition

Published on: August 27, 2013

36.5K
Detection of Alternative Splicing During Epithelial-Mesenchymal Transition11:48

Detection of Alternative Splicing During Epithelial-Mesenchymal Transition

Published on: October 9, 2014

13.4K

Related Concept Videos

Escape Velocity01:26

Escape Velocity

The escape velocity of an object is defined as the minimum initial velocity that it requires to escape the surface of another object to which it is gravitationally bound and never to return. For example, what would be the minimum velocity at which a satellite should be launched from the Earth's surface such that it just escapes the Earth's gravitational field?
To calculate the escape velocity, it is assumed that no energy is lost to any frictional forces. In practice, a satellite...
8.3K
Escape Velocities of Gases01:19

Escape Velocities of Gases

To escape the Earth's gravity, an object near the top of the atmosphere at an altitude of 100 km must travel away from Earth at 11.1 km/s. This speed is called the escape velocity. The temperature at which gas molecules attain the rms speed, which is equal to the escape velocity, can be estimated by using the equation for the average kinetic energy of the gas molecules. According to the kinetic theory of gas, the average kinetic energy of the gas molecules is proportional to its...
1.3K
Plasticizers01:31

Plasticizers

Water-reducers, or plasticizers, are chemical admixtures used in concrete to improve strength and workability. These additives reduce the water-cement ratio without compromising workability, lower the cement content while maintaining the same workability, or increase workability to assist concrete placement in inaccessible areas.
Plasticizers function by using surface-active agents to create repulsive electrostatic forces between cement particles. This dispersion enhances the concrete's...
355
Plasticity00:58

Plasticity

Plasticity is the property where an object loses its elasticity and undergoes irreversible deformation, even after the deformation forces are eliminated. If a material deforms irreversibly without increasing stress or load, then this is called ideal plasticity. For example, when a force is applied to an aluminum rod, it changes its shape, but it does not return to its original shape once the force is removed. Plastic deformation or ductility is thus a permanent deformation or change in the...
3.0K
Metastasis02:30

Metastasis

Metastasis is the spread of cancer cells from the original site to distant locations in the body. Cancer cells can spread via blood vessels (hematogenous) as well as lymph vessels in the body.
Epithelial-to-Mesenchymal Transition
The epithelial-to-mesenchymal transition or EMT is a developmental process commonly observed in wound healing, embryogenesis, and cancer metastasis. EMT is induced by transforming growth factor-beta (TGF-β) or receptor tyrosine kinase (RTK) ligands, which further...
6.4K
Plastic Behavior01:21

Plastic Behavior

A material's elastic behavior is characterized by the disappearance of stress once the load is removed, allowing the material to return to its original state. However, when stress surpasses the yield point, yielding commences, marking the onset of plastic deformation or permanent set. This change from elastic to plastic behavior is influenced by the peak stress value and the duration before the load is removed. An intriguing observation occurs when a specimen is loaded, unloaded, and...
539