Related Experiment Video

Updated: Jan 23, 2026

Author Spotlight: Cost-Effective Transcriptomic Drug Screening - Unlocking New Targets
06:40

Author Spotlight: Cost-Effective Transcriptomic Drug Screening - Unlocking New Targets

Published on: February 23, 2024

1.8K

Achieving cost-efficient management of drug supply via economic order quantity and minimum-maximum stock level

Ertha Kusuma Dewi1, Maznah Dahlui2, Djazuly Chalidyanto3

  • 1Faculty of Public Health, Universitas Airlangga , Surabaya, Indonesia.

Expert Review of Pharmacoeconomics & Outcomes Research
|June 18, 2019
PubMed
Abstract

Keywords:
Economic order quantityopportunity costopportunity lossshortagestagnant

More Related Videos

Tuning Degradation to Achieve Specific and Efficient Protein Depletion05:11

Tuning Degradation to Achieve Specific and Efficient Protein Depletion

Published on: July 20, 2019

6.6K
NMR-Based Fragment Screening in a Minimum Sample but Maximum Automation Mode09:19

NMR-Based Fragment Screening in a Minimum Sample but Maximum Automation Mode

Published on: June 4, 2021

3.8K

Related Concept Videos

Determination of Multiple Dosing Parameters: Steady-State, Minimum and Maximum Concentrations01:15

Determination of Multiple Dosing Parameters: Steady-State, Minimum and Maximum Concentrations

Gentamicin, an aminoglycoside antibiotic, is commonly administered via intermittent intravenous infusion to treat severe infections. An intermittent one-hour infusion of gentamicin, administered at eight-hour intervals, allows for precise control of plasma drug concentrations, minimizing toxicity while ensuring therapeutic efficacy. Pharmacokinetic principles govern the dynamics of plasma concentrations and can be mathematically described using specific equations.The plasma drug concentration...
240
Base Quantities and Derived Quantities01:14

Base Quantities and Derived Quantities

In any system of units, the units for some physical quantities must be specified through a measurement process. These measurements are the base quantities of the system, and their units are the base units of the system. The algebraic combinations of the base values can then be used to express all other physical quantities. Each of these physical quantities is then referred to as a derived quantity, with each unit being referred to as a derived unit.
The International Organization for...
26.0K
Maximum Deflection01:13

Maximum Deflection

When analyzing beams under unsymmetrical loads, such as a train moving on a bridge, it is crucial to accurately determine the points of maximum stress and deflection. The process involves identifying the maximum deflection of the beam, which may not always occur at its midpoint due to the uneven distribution of the load.
The maximum deflection occurs at a specific point, known as point O, where the tangent to the deflection curve is horizontal. To find point O, the slope of the tangent at any...
1.0K
Maximum Power Transfer01:16

Maximum Power Transfer

Numerous practical applications within engineering disciplines, such as telecommunications, necessitate optimizing power delivery to a connected load. This pursuit, however, entails inherent internal losses, which can either equal or exceed the power supplied to the load. The Thevenin equivalent circuit is helpful in finding the maximum power a linear circuit can deliver to a load. It is assumed in this context that the load resistance can be adjusted.
By substituting the entire circuit with...
854
Maximum Size of Aggregate01:12

Maximum Size of Aggregate

The maximum size of aggregate is defined as the aperture of the sieve retaining 15 percent or more of the particles present in the aggregate sample. The aggregate's maximum size impacts the concrete's water requirement, workability, and strength. Larger aggregates reduce the surface area needing cement paste coverage, which can lower water needs, thereby allowing a decrease in the water-to-cement ratio when the desired workability and richness of the mix are to be maintained, which can...
532
Estimation of the Physical Quantities01:05

Estimation of the Physical Quantities

On many occasions, physicists, other scientists, and engineers need to make estimates of a particular quantity. These are sometimes referred to as guesstimates, order-of-magnitude approximations, back-of-the-envelope calculations, or Fermi calculations. The physicist Enrico Fermi was famous for his ability to estimate various kinds of data with surprising precision. Estimating does not mean guessing a number or a formula at random. Instead, estimation means using prior experience and sound...
7.4K