Related Experiment Video

Updated: Jan 23, 2026

Construction of a Wireless-Enabled Endoscopically Implantable Sensor for pH Monitoring with Zero-Bias Schottky Diode-based Receiver
08:25

Construction of a Wireless-Enabled Endoscopically Implantable Sensor for pH Monitoring with Zero-Bias Schottky Diode-based Receiver

Published on: August 27, 2021

2.9K

Circuit Parameters of a Receiver Coil Using a Wiegand Sensor for Wireless Power Transmission

Katsuki Takahashi1, Tsutomu Yamada2, Yasushi Takemura3

  • 1Electrical and Computer Engineering, Yokohama National University, Yokohama 240-8501, Japan. kono-katsuki-rj@ynu.jp.

Sensors (Basel, Switzerland)
|June 19, 2019
PubMed

Keywords:
FeCoV wirelarge Barkhausen jumpmagnetization reversalwiegand sensor

More Related Videos

In Vitro Application of a Wireless Sensor in Flexion-Extension Gap Balance of Unicompartmental Knee Arthroplasty07:33

In Vitro Application of a Wireless Sensor in Flexion-Extension Gap Balance of Unicompartmental Knee Arthroplasty

Published on: May 5, 2023

1.1K
Implantation and Control of Wireless, Battery-free Systems for Peripheral Nerve Interfacing07:13

Implantation and Control of Wireless, Battery-free Systems for Peripheral Nerve Interfacing

Published on: October 20, 2021

3.9K

Related Concept Videos

Power in a Three-Phase Circuit01:15

Power in a Three-Phase Circuit

Three-phase systems have two configurations: the wye and delta. A star configuration can be three or four wires; in a delta configuration, the components are connected in a closed loop. Instantaneous power refers to the power value at a precise moment, and in a balanced three-phase system, it is constant. This is because the sum of the instantaneous powers in the three phases remains steady over time, despite individual fluctuations, due to the symmetry and phase relationship. The total...
611
Power in an AC Circuit01:26

Power in an AC Circuit

In a DC circuit, the power consumed is simply the product of the DC voltage times the DC current, given in watts. However, the power consumed for AC circuits with reactive components is calculated differently. Since electrical power is the "rate" at which energy is used in a circuit, all electrical and electronic components and devices have a safe operating range for electrical power.
In a DC circuit, there is no sinusoidal waveform associated with the supply; the voltages and currents are...
2.3K
Power System Three-Phase Short Circuits01:21

Power System Three-Phase Short Circuits

Determining the subtransient fault current in a power system involves representing transformers by their leakage reactances, transmission lines by their equivalent series reactances, and synchronous machines as constant voltage sources behind their subtransient reactances. In this analysis, certain elements are excluded, such as winding resistances, series resistances, shunt admittances, delta-Y phase shifts, armature resistance, saturation, saliency, non-rotating impedance loads, and small...
534
Power Dissipated in a Circuit: Problem Solving01:15

Power Dissipated in a Circuit: Problem Solving

The equivalent resistance of a combination of resistors depends on their values and how they are connected.
The simplest combinations of resistors are series and parallel connections. In a series circuit, the first resistor's output current flows into the second resistor's input; therefore, each resistor's current is the same. Thus, the equivalent resistance is the algebraic sum of the resistances. The current through the circuit can be found from Ohm's law and is equal to the...
1.6K
Power Distribution in Three-phase and Single Phase Circuits01:17

Power Distribution in Three-phase and Single Phase Circuits

Power distribution within electrical circuits is a foundational aspect of residential and industrial energy systems. While single-phase power is common in residential settings, three-phase power is the standard for industrial environments with heavy machinery. Each system is different and has advantages, and it's crucial to understand the underlying principles of power distribution and material efficiency.
Single-Phase Power Distribution:
Single-phase circuits are typical in household settings;...
611
Receiver Operating Characteristic Plot01:15

Receiver Operating Characteristic Plot

A ROC (Receiver Operating Characteristic) plot is a graphical tool used to assess the performance of a binary classification model by illustrating the trade-off between sensitivity (true positive rate) and specificity (false positive rate). By plotting sensitivity against 1 - specificity across various threshold settings, the ROC curve shows how well the model distinguishes between classes, with a curve closer to the top-left corner indicating a more accurate model. The area under the ROC curve...
479