Related Experiment Video

Updated: Jan 23, 2026

Fabrication of a Bioactive, PCL-based "Self-fitting" Shape Memory Polymer Scaffold
09:37

Fabrication of a Bioactive, PCL-based "Self-fitting" Shape Memory Polymer Scaffold

Published on: October 23, 2015

13.4K

Structural Change in Ni-Fe-Ga Magnetic Shape Memory Alloys after Severe Plastic Deformation

Gheorghe Gurau1, Carmela Gurau2, Felicia Tolea3

  • 1Faculty of Engineering, "Dunărea de Jos" University of Galati, Domnească Street, 47, RO-800008 Galati, Romania. gheorghe.gurau@ugal.ro.

Materials (Basel, Switzerland)
|June 20, 2019
PubMed

Keywords:
Ferromagnetic shape memory alloysHSHPTNi-Fe-GaSPDsevere plastic deformationultrafine-grained materials

More Related Videos

Three-Dimensional Shape Modeling and Analysis of Brain Structures05:33

Three-Dimensional Shape Modeling and Analysis of Brain Structures

Published on: November 14, 2019

7.6K
Shape Memory Polymers for Active Cell Culture10:53

Shape Memory Polymers for Active Cell Culture

Published on: July 4, 2011

13.9K

Related Concept Videos

Plastic Deformations01:19

Plastic Deformations

Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their...
442
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
412
Plastic Deformation in Circular Shafts01:20

Plastic Deformation in Circular Shafts

When materials are subjected to forces that surpass their yield strength, they undergo a process known as plastic deformation. This results in a permanent alteration or strain in their structure. This concept can be specifically applied to circular shafts, where the deformation leads to a change in its shape. The precise evaluation of this plastic deformation requires understanding the stress distribution within the circular shaft, which is achieved by calculating the maximum shearing stress in...
449
Plastic Deformations of Members with a Single Plane of Symmetry01:21

Plastic Deformations of Members with a Single Plane of Symmetry

When a structural member undergoes plastic deformation due to bending, it is crucial to understand the position of the neutral axis and the stress distribution. This member, characterized by a single plane of symmetry, exhibits a uniform stress distribution, with negative stress above the neutral axis and positive stress below. Notably, the neutral axis does not align with the centroid of the cross-section. This misalignment is typical in cases where the cross-section is not rectangular or...
348
Global Climate Change01:50

Global Climate Change

Throughout its ~4.5 billion year history, the Earth has experienced periods of warming and cooling. However, the current drastic increase in global temperatures is well outside of the Earth’s cyclic norms, and evidence for human-caused global climate change is compelling. Paleoclimatology, the study of ancient climate conditions, provides ample evidence for human-caused global climate change by comparing recent conditions with those in the past.
28.8K
Plasticizers01:31

Plasticizers

Water-reducers, or plasticizers, are chemical admixtures used in concrete to improve strength and workability. These additives reduce the water-cement ratio without compromising workability, lower the cement content while maintaining the same workability, or increase workability to assist concrete placement in inaccessible areas.
Plasticizers function by using surface-active agents to create repulsive electrostatic forces between cement particles. This dispersion enhances the concrete's...
353