Related Experiment Video

Updated: Jan 22, 2026

High-Speed Optical Diagnostics of a Supersonic Ping-Pong Cannon
05:40

High-Speed Optical Diagnostics of a Supersonic Ping-Pong Cannon

Published on: March 24, 2023

2.5K

Supersonic Transporter Deformity in Transgender Men following Phalloplasty

Christopher J Salgado1, Lydia A Fein1, Eva A Williams1

  • 1From the Division of Plastic, Aesthetic, and Reconstructive Surgery, Department of Surgery, and the Department of Obstetrics and Gynecology, University of Miami Miller School of Medicine.

Plastic and Reconstructive Surgery
|June 28, 2019
PubMed

More Related Videos

A Microfluidic Technique to Probe Cell Deformability09:47

A Microfluidic Technique to Probe Cell Deformability

Published on: September 3, 2014

11.8K
Tracking Morphogenetic Tissue Deformations in the Early Chick Embryo08:19

Tracking Morphogenetic Tissue Deformations in the Early Chick Embryo

Published on: October 17, 2011

13.3K

Related Concept Videos

Plastic Deformations01:19

Plastic Deformations

Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their...
439
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
412
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
373
Deformations in a Symmetric Member in Bending01:18

Deformations in a Symmetric Member in Bending

When analyzing the deformation of a symmetric prismatic member subjected to bending by equal and opposite couples, it becomes clear that as the member bends, the originally straight lines on its wider faces curve into circular arcs, with a constant radius centered at a point known as Point C. This phenomenon helps to understand the stress and strain distribution within the member more clearly.
When the member is segmented into tiny cubic elements, it is observed that the primary stress...
482
Facilitated Transport01:19

Facilitated Transport

The chemical and physical properties of plasma membranes cause them to be selectively permeable. Since plasma membranes have both hydrophobic and hydrophilic regions, substances need to be able to transverse both regions. The hydrophobic area of membranes repels substances such as charged ions. Therefore, such substances need special membrane proteins to cross a membrane successfully. In  facilitated transport, also known as facilitated diffusion, molecules and ions travel across a...
146.6K
Deformation of Member under Multiple Loadings01:11

Deformation of Member under Multiple Loadings

When a rod is made of different materials or has various cross-sections, it must be divided into parts that meet the necessary conditions for determining the deformation. These parts are each characterized by their internal force, cross-sectional area, length, and modulus of elasticity. These parameters are then used to compute the deformation of the entire rod.
In the case of a member with a variable cross-section, the strain is not constant but depends on the position. The deformation of an...
453