Early Quantitative Partial Weight-Bearing Exercise After Periarticular Fractures of the Tibia Using a Lower-Body

Ju Chan Kim1, Ja Ho Leigh, Jun Young Jang

  • 1From the Department of Rehabilitation Medicine, Seoul National University Hospital, Seoul, Republic of Korea (JCK, JYJ, HSN, SGC); Department of Rehabilitation Medicine, Incheon St. Mary's Hospital, College of Medicine, The Catholic University of Korea, Incheon, Republic of Korea (JHL); Department of Rehabilitation Medicine, Incheon Workers Compensation Hospital, Incheon, Republic of Korea (JYJ, HSN); Department of Orthopedic Surgery, Seoul National University Bundang Hospital, Seongnam, Republic of Korea (J-KK); Department of Orthopedic Surgery, Korea University Guro Hospital, Seoul, Republic of Korea (J-WC, J-KO); Department of Biomedical Engineering, Seoul National University College of Medicine, Seoul, Republic of Korea (HSN); Y.H.C. Research & Development Team, Korea Orthopedics and Rehabilitation Engineering Center, Seoul, Republic of Korea (YHC); and Department of Rehabilitation Medicine, Asan Medical Center, College of Medicine, University of Ulsan (SHL).

Related Concept Videos

Mixtures of Gases: Dalton's Law of Partial Pressures and Mole Fractions03:03

Mixtures of Gases: Dalton's Law of Partial Pressures and Mole Fractions

Unless individual gases chemically react with each other, the individual gases in a mixture of gases do not affect each other’s pressure. Each gas in a mixture exerts the same pressure that it would exert if it were present alone in the container. The pressure exerted by each individual gas in a mixture is called its partial pressure.
43.7K
Dalton's Law of Partial Pressure01:11

Dalton's Law of Partial Pressure

The partial pressure of a gas is a measure of the thermodynamic activity of the gas's molecules. The pressure that a gas would create if it occupied the total volume available is called the gas's partial pressure. If two or more gases are mixed together in a container, the molecules move randomly and collide with each other, causing them to reach thermal equilibrium. When the gases have the same temperature, their molecules have the same average kinetic energy. Thus, each gas obeys the...
2.5K
Bones of the Lower Limb: Tibia and Fibula01:10

Bones of the Lower Limb: Tibia and Fibula

The tibia is the main weight-bearing bone of the lower leg. It is larger than the fibula with which it is paired. The tibia is also the second longest bone in the body and is located right below the skin. The proximal end of the tibia forms the medial and the lateral condyle, which articulates with the condyles of the femur to form the knee joint. Between the articulating surfaces is the irregular elevated area known as the intercondylar eminence that serves as the inferior attachment point for...
9.0K
Actin Treadmilling01:18

Actin Treadmilling

Actin filaments undergo polymerization and depolymerization from either end. The polymerization and depolymerization rates depend on the cytosolic concentration of free G-actins. The polymerization rate is generally higher at the plus or barbed end, while the depolymerization rate is higher at the minus or pointed end. At a steady state, critical concentration describes the concentration of free G-actin monomers at which the polymerization rate at the plus end is equal to that of the...
9.6K
Weighted Mean00:57

Weighted Mean

While taking the arithmetic, geometric, or harmonic mean of a sample data set, equal importance is assigned to all the data points. However, all the values may not always be equally important in some data sets. An intrinsic bias might make it more important to give more weightage to specific values over others.
For example, consider the number of goals scored in the matches of a tournament. While computing the average number of goals scored in the tournament, it may be more important to...
6.2K
Pivot Bearings01:23

Pivot Bearings

In mechanical systems, bearings are crucial in facilitating relative motion between two components while minimizing friction and wear. They help distribute various loads (radial, axial or a combination of both loads) across machinery parts, ensuring smooth and efficient operation.
A pivot bearing is a specialized type of bearing designed to support axial loads on a rotating shaft. The bearing surface, or the pivot, is positioned at the end of a shaft to support the axial thrust. The pivot may...
2.2K