Related Experiment Video

Updated: Jan 22, 2026

Measurements of Waves in a Wind-wave Tank Under Steady and Time-varying Wind Forcing
08:54

Measurements of Waves in a Wind-wave Tank Under Steady and Time-varying Wind Forcing

Published on: February 13, 2018

9.1K

Pitch angle control of a wind turbine operating above the rated wind speed: A sliding mode control approach

L Colombo1, M L Corradini2, G Ippoliti1

  • 1Dipartimento di Ingegneria dell'Informazione, Università Politecnica delle Marche, Via Brecce Bianche, 60131 Ancona, Italy.

ISA Transactions
|July 20, 2019
PubMed

Keywords:
Pitch controlSliding mode controlWind turbines

More Related Videos

A Wind Tunnel for Odor Mediated Insect Behavioural Assays05:25

A Wind Tunnel for Odor Mediated Insect Behavioural Assays

Published on: November 30, 2018

12.4K
Wind Tunnel Experiments to Study Chaparral Crown Fires09:27

Wind Tunnel Experiments to Study Chaparral Crown Fires

Published on: November 14, 2017

10.1K

Related Concept Videos

Wind Turbine Machine Models01:24

Wind Turbine Machine Models

In the growing field of wind energy, incorporating wind turbine models into transient stability analysis is essential. Induction and synchronous machines are the primary models used, with induction machines being prevalent due to their simplicity and reliability.
Induction machines interact through the rotating magnetic field generated by the stator and the rotor. The key parameter is slip, which is the difference between synchronous speed and rotor speed relative to synchronous speed. Slip is...
563
Turbine-Governor Control01:17

Turbine-Governor Control

Turbine-governor control is crucial for maintaining power system stability by balancing turbine mechanical power output with electrical load demand. This mechanism ensures that generator frequency and rotor speed are within acceptable limits during load variations. Turbine-generator units store kinetic energy due to their rotating masses; this energy is released to meet the load requirement when the load increases. The electrical torque of turbines rises to meet the demand, whereas the...
937
Three-Winding Transformers01:19

Three-Winding Transformers

Three identical single-phase transformers can be configured to form a three-phase transformer connection, which involves high-voltage and low-voltage windings. The high-voltage windings are denoted by capital letters A-B-C, while the low-voltage windings are labeled with lowercase letters a-b-c, representing their respective phases. This notation helps distinguish between the high and low voltage sides of the transformer.
In the per-unit equivalent circuit of a grounded Y-Y three-phase...
693
Types of Biopharmaceutical Studies: Controlled and Non-Controlled Approaches01:23

Types of Biopharmaceutical Studies: Controlled and Non-Controlled Approaches

Biopharmaceutical studies constitute a vital field aiming to enhance drug delivery methods and refine therapeutic approaches, drawing upon diverse interdisciplinary knowledge. In research methodologies, the choice between controlled and non-controlled studies significantly influences the study's reliability and accuracy.
Non-controlled studies, commonly employed for initial exploration, lack a control group, rendering them susceptible to biases and external influences. In contrast,...
414
Modes of Operations of BJT01:21

Modes of Operations of BJT

A Bipolar Junction Transistor (BJT) is a versatile component in electronics, functioning in four distinct modes based on the biasing of its junctions: active, saturation, cut-off, and inverted modes.
Active Mode: The most common mode for amplification, the active mode features a forward-biased emitter-base junction and a reverse-biased base-collector junction. This setup enables electrons to be injected from the emitter to the base while blocking the majority carriers at the collector. The...
2.0K
Design Example: Calculating Safe Diameter for Wind-Exposed Disc01:17

Design Example: Calculating Safe Diameter for Wind-Exposed Disc

Assessing safety in wind-exposed installations is crucial to preventing potential failures. This example explores the calculation and design adjustments needed to mount a circular disc on a building facade, where wind forces are a primary concern. A 4-meter diameter disc was initially designed as an aesthetic feature facing winds at a velocity of 25 meters per second, with an air density of 1.25 kilograms per cubic meter. Given these conditions, the drag force on the disc was determined using...
357