Repeated Intraperitoneal Administration of Low-Concentration Methylcellulose Leads to Systemic Histologic Lesions

Stacey Meeker1, Megan Beckman1, Kevin M Knox1

  • 1Department of Comparative Medicine, School of Medicine (S.M., P.M.T.), Department of Biology, College of Arts and Sciences (M.B.), and Department of Pharmacy, School of Pharmacy (M.B., K.M.K., M.B.-H.), University of Washington, Seattle, Washington.

Insights

Repeated intraperitoneal injections of methylcellulose (MC) cause organ damage in mice, but oral MC does not. This inflammation impacts research findings by mimicking drug side effects.

Area of Science:

  • Preclinical research methodology
  • Toxicology and pathology
  • Pharmacology

Background:

  • Methylcellulose (MC) is a common vehicle for drug delivery in preclinical studies.
  • Oral administration of MC is FDA-approved as safe.
  • Limited data exists on the safety and impact of repeated intraperitoneal (IP) MC administration.

Purpose of the Study:

  • To investigate the hypothesis that chronic IP administration of 0.5% MC causes histologic lesions.
  • To determine if these lesions affect the phenotype of a preclinical disease model.
  • To compare the effects of IP versus oral (PO) administration of MC.

Main Methods:

  • Male CF-1 mice received twice-weekly IP or PO injections of 0.5% MC or saline for 6 weeks.
  • Mice were part of a seizure model, with treatments administered after seizure induction.
  • Histopathological analysis was performed on a subset of mice; phenotypic assessments included body weight, appearance, seizure stability, and behavior.

Main Results:

  • IP administration of 0.5% MC induced lesions in multiple organs (kidney, liver, lymph nodes, etc.) in all treated mice (7/7).
  • No lesions were observed in mice receiving PO MC or saline (IP or PO).
  • IP MC treatment did not affect body weight, appearance, seizure stability, or behavior.

Conclusions:

  • Repeated IP administration of 0.5% MC causes systemic organ damage without altering the preclinical model's phenotype.
  • This organ damage may be misinterpreted as drug-induced lesions, confounding research results.
  • Oral administration of MC does not appear to cause these adverse effects.

Related Concept Videos

Line Loss01:10

Line Loss

The different configurations of source-load connections include wye (star) and delta connections. The relationship between line and phase voltages and currents varies depending on the configuration. When the source is supplying power, it is transmitted through the wires to the load, and during this transmission, some power is absorbed by the wires, leading to line loss.
Line loss impacts power delivery efficiency in a balanced three-phase circuit. The symmetry in such a circuit simplifies the...
517
Reducing Line Loss01:18

Reducing Line Loss

In a three-phase circuit, line loss is an indicator of energy dissipated as heat due to the resistance of transmission lines. To address this, incorporating transformers into the system—a step-up transformer at the source and a step-down transformer at the load—is a strategic solution. Two three-phase transformers are introduced to improve this.
With a step-up transformer at the source, the voltage is increased, thereby reducing the current in the transmission lines since power loss in...
370
Concentration Cells02:41

Concentration Cells

A concentration cell is a type of a  voltaic cell constructed by connecting two almost identical half-cells, both based on the same half-reaction and using the same electrode, differing only in the concentration of one redox species. A concentration cell's potential, therefore, is determined only by the concentration difference of the particular redox species.
Consider the following voltaic cell:
25.6K
Major Losses in Pipes01:28

Major Losses in Pipes

When a fluid flows through a pipe, it experiences energy losses due to frictional resistance along the pipe walls, known as major losses. These energy losses result in a pressure drop, which varies based on the flow conditions — whether laminar or turbulent — and the specific physical properties of the fluid and pipe.
Fluid flow can be classified as laminar or turbulent, primarily based on the Reynolds number. This dimensionless number reflects the relative influence of inertial to viscous...
1.9K
Minor Losses in Pipes01:25

Minor Losses in Pipes

In pipe systems, minor losses refer to energy losses arising from components such as valves, bends, fittings, expansions, and other features that disrupt the steady flow of fluid. These disturbances cause energy dissipation through turbulence and resistance, which engineers quantify to manage system efficiency effectively.
Valves play a significant role in generating minor losses by obstructing or redirecting the fluid flow. When a valve is closed or partially closed, it restricts the flow...
1.9K
Energy Losses in Transformers01:21

Energy Losses in Transformers

In an ideal transformer, it is assumed that there are no energy losses, and, hence, all the power at the primary winding is transferred to the secondary winding. However, in reality,  the transformers always have some energy losses, and, hence, the output power obtained at the secondary winding is less than the input power at the primary winding due to energy losses.
There are four main reasons for energy losses in transformers.
The first cause can be  the high resistance of the...
1.3K