Related Experiment Video

Updated: Jan 20, 2026

High-pressure, High-temperature Deformation Experiment Using the New Generation Griggs-type Apparatus
12:30

High-pressure, High-temperature Deformation Experiment Using the New Generation Griggs-type Apparatus

Published on: April 3, 2018

19.4K

Deformation analysis of suspended type cut off wall of diversion structures

S Sivakumar1,2, N Almas Begum3, P V Premalatha4

  • 1PRIST (Deemed to be University), Vallam, Thanjavur, 626023, Tamilnadu, India.

Heliyon
|August 21, 2019
PubMed

Keywords:
Civil engineeringComputer-aided engineeringCutoff wallEarth sciencesPartial seepage barriersSeepage dynamic forceSeepage flowStructural engineeringSuspended type cutoff wall

More Related Videos

A Novel Bayesian Change-point Algorithm for Genome-wide Analysis of Diverse ChIPseq Data Types12:39

A Novel Bayesian Change-point Algorithm for Genome-wide Analysis of Diverse ChIPseq Data Types

Published on: December 10, 2012

11.7K
Author Spotlight: Investigating the Role of Repetitive DNA Misregulation in Cancer Initiation and Immunotherapy Resistance04:58

Author Spotlight: Investigating the Role of Repetitive DNA Misregulation in Cancer Initiation and Immunotherapy Resistance

Published on: December 13, 2024

4.0K

Related Concept Videos

Plant Cell Wall02:43

Plant Cell Wall

The plant cell wall gives plant cells shape, support, and protection. As a cell matures, its cell wall specializes according to the cell type. For example, the parenchyma cells of leaves possess only a thin, primary cell wall.
60.1K
Types of Non-structural Cracks in Concrete01:28

Types of Non-structural Cracks in Concrete

Non-structural cracks are primarily of three types: plastic, early-age thermal, and drying shrinkage cracks. Plastic cracks are further classified into plastic shrinkage cracks and plastic settlement cracks.
Plastic shrinkage cracks typically form within hours after the concrete is poured. The concrete's surface dries faster than the bottom, creating tensile stress that the still-plastic concrete cannot withstand, leading to diagonal or randomly patterned cracks on the concrete surface.
479
Plastic Deformations01:19

Plastic Deformations

Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their...
436
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
407
Accessory Structures of the Skin: Hair Growth and Types01:20

Accessory Structures of the Skin: Hair Growth and Types

Hair growth begins with the production of keratinocytes by the basal cells of the hair bulb. As new cells are deposited at the hair bulb, the hair shaft is pushed through the follicle toward the surface. Keratinization is completed as the cells are pushed to the skin surface to form the shaft of hair that is externally visible. The external hair is completely dead and composed entirely of keratin. Hair can be cut or shaven without damaging the hair structure because the cut is superficial. Most...
2.3K
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
369