Related Experiment Video

Updated: Jan 20, 2026

Aerosol-assisted Chemical Vapor Deposition of Metal Oxide Structures: Zinc Oxide Rods
06:39

Aerosol-assisted Chemical Vapor Deposition of Metal Oxide Structures: Zinc Oxide Rods

Published on: September 14, 2017

13.6K

Evaluation of Aerosol Electrospray Analysis of Metal-on-Metal Wear Particles from Simulated Total Joint Replacement

Gobert von Skrbensky1, Karoline Mühlbacher2,3, Emir Benca4

  • 1Department of Orthopedics and Trauma Surgery, Medical University of Vienna, Währinger Gürtel 18-20, 1090 Vienna, Austria.

Sensors (Basel, Switzerland)
|September 5, 2019
PubMed

Keywords:
debrisimplantsparticlesprosthesiswear

More Related Videos

Knowledge Based Cloud FE Simulation of Sheet Metal Forming Processes11:05

Knowledge Based Cloud FE Simulation of Sheet Metal Forming Processes

Published on: December 13, 2016

12.6K
Author Spotlight: Advancing Therapeutics with Biocompatible Sodium Alginate Hydrogel Microspheres07:24

Author Spotlight: Advancing Therapeutics with Biocompatible Sodium Alginate Hydrogel Microspheres

Published on: June 7, 2024

2.9K

Related Concept Videos

Aerosol-assisted Chemical Vapor Deposition of Metal Oxide Structures: Zinc Oxide Rods06:39

Aerosol-assisted Chemical Vapor Deposition of Metal Oxide Structures: Zinc Oxide Rods

Columnar zinc oxide structures in the form of rods are synthesized via aerosol-assisted chemical vapor deposition without the use of pre-deposited catalyst-seed particles. This method is scalable and compatible with various substrates based on either silicon, quartz or...
13.6K
Metallic Solids02:37

Metallic Solids

Metallic solids such as crystals of copper, aluminum, and iron are formed by metal atoms. The structure of metallic crystals is often described as a uniform distribution of atomic nuclei within a “sea” of delocalized electrons. The atoms within such a metallic solid are held together by a unique force known as metallic bonding that gives rise to many useful and varied bulk properties.
All metallic solids exhibit high thermal and electrical conductivity, metallic luster, and malleability....
20.5K
Knowledge Based Cloud FE Simulation of Sheet Metal Forming Processes11:05

Knowledge Based Cloud FE Simulation of Sheet Metal Forming Processes

The following paper presents a novel FE simulation technique (KBC-FE), which reduces computational cost by performing simulations on a cloud computing environment, through the application of individual modules. Moreover, it establishes a seamless collaborative network between world leading scientists, enabling the integration of cutting edge knowledge modules into FE...
12.6K
Preparation of Cross-Linked Sodium Alginate Microspheres with Different Metal Ions Using the Microfluidic Electrospray Technology07:24

Preparation of Cross-Linked Sodium Alginate Microspheres with Different Metal Ions Using the Microfluidic Electrospray Technology

The protocol describes the preparation of sodium alginate microspheres cross-linked with different metal ions using a microfluidic device for drug carrier design. The antimicrobial properties and slow drug release of these microspheres were also...
2.9K
Bonding in Metals02:32

Bonding in Metals

Metallic bonds are formed between two metal atoms. A simplified model to describe metallic bonding has been developed by Paul Drüde called the “Electron Sea Model”. 
52.0K
Alkali Metals03:06

Alkali Metals

Group 1 elements are soft and shiny metallic solids. They are malleable, ductile, and good conductors of heat and electricity. The melting points of the alkali metals are unusually low for metals and decrease going down the group, while the density increases going down the group with the exception of potassium (Table 1).
Table 1: Properties of the alkali metals
24.2K